10689582700 Kenmore Ice Maker - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from North Wilkesboro, NC
- Parts Used:
- W11566405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
was not making ice
diagnosed no water flow over evaporator checked voltage into pump then checked pump with ohm meter ordered pump and installed by removing access cover and water holding assembly installed new pump replaced water holding assembly and access cover and returned icemaker to service all is well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Chickasha, OK
- Parts Used:
- W11566405
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
No water flow
Took the two pumps tested them with 12 volt Battery. one pump didn't work. Looked up part nomber on Google and it lead me to this Co.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Galesburg, IL
- Parts Used:
- W11566405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water not flowing over cooling plate
Removed ice scoop and holder. Remove front cover and pump bracket. Replaced pump and replaced covers. Started up and working well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LARRY from INDIO, CA
- Parts Used:
- W11566405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Stopped making ice
I called a repairman to come out and he said it would cost $320 dollars for the repair. So I bought the part and spent $85 dollars and about 25 minutes to repair it myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LANDRUM, SC
- Parts Used:
- WPW10548509
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice maker would not make ice. I went through diagnostics and it showed the level sensor was not working. Water would continue filling the reservoir and not shut off to start making ice.
Took off several plastic covers to gain better accessibility to the sensor. Had to pull out the whole support piece to get at the part. Took out the old sensor, cleaned the unit as best as possible, then installed the replacement. Turned on the power to the unit and reinstalled all the parts I took out for better viewing and accessibility. Started up the unit and it is slowly building ice, which I will remove and dispose of to start getting clean ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Pittsburg, TX
- Parts Used:
- W11566405
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Ice Maker leaking proved to be a cracked value (not pump)
We had the coldest winter in 114 years in north Texas (must be global warming...) and our outdoor kitchen ice maker value assembly frozen and cracked.
1) Remove bottom panel screws using nut driver
2) Remove door screws
3) Unhook two power connectors from value assembly
4) Release water supply quick connects
5) Replace value
6) Re-install door - this is a a little tricky there is a spring on each side which slows the door when opening and this pulls the door down which means the screw are not properly aligned by default. You basically have to pull the door up( a second set of hands help) and attach the screws and then let it go.
1) Remove bottom panel screws using nut driver
2) Remove door screws
3) Unhook two power connectors from value assembly
4) Release water supply quick connects
5) Replace value
6) Re-install door - this is a a little tricky there is a spring on each side which slows the door when opening and this pulls the door down which means the screw are not properly aligned by default. You basically have to pull the door up( a second set of hands help) and attach the screws and then let it go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimena from FARMINGTON, CT
- Parts Used:
- W11566405
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Old pump gave up
Followed instructions in Sears parts website. Not difficult but tricky to get screws out and back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from HEBER SPRINGS, AR
- Parts Used:
- WPW10548509
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
only a partial refill of water bucket (would then run dry and make pump noise)
my sensor was stuck because of age, so I had to remove the water bucket to pry it out. It is easy to see what you have to remove to get to it. I used the mirror and rachet, extensions, 1/4 socket to remove screws. Tips - Remove the plastic door-inner to help working inside the bin. Also plug the drain because you will drop screws. Magnet sockets don't work on stainless steel. Later I found it is much easier to work inside the bin by pulling the entire unit out (shut off water and power, remove lower panel and disconnect drain tube). It sounds hard, but actually is easy. REMOVE THE TOP (4 screws). it stays connected because of wiring, but it allows full access and makes all kinds of repairs easy, especially pump replacement and even the circuit board behind the front panel buttons if you ever get to that point.
BTW Partselect is awesome, I have used a number of times for ice maker and dishwasher. My next project is the washing machine! Always the right part shipped very quickly.
BTW Partselect is awesome, I have used a number of times for ice maker and dishwasher. My next project is the washing machine! Always the right part shipped very quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Guy from SURFSIDE BCH, SC
- Parts Used:
- W11566405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Disherwasher would not start
Found fault with recirculating pump. Found hot spot on pump circuit board . Replaced pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Floyd from VIAN, OK
- Parts Used:
- WPW10548509
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Sensor quit working
Removed and replaced sensor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Flowery Branch, GA
- Parts Used:
- 2313702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Under counter Ice maler not making Ice
Had repair man out to make repair his price for part $219.00 and $271.00 labor as he was looking up his price I got on line and found part here for $121.00 thought it might take me 1 hour to fix only 6- 1/4" nuts 2 screws and less than 30 min I had Ice maker working. Bottom line my total cost $75.00 repar man $121.00 part $196.00 that was a savings of $294.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Battle creek, MI
- Parts Used:
- W11566405
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Recirculating pump stopped working
Remove ice tray and guard over moter. Un plug the 3 plugs and pull the entire motor assembly out. Use a screw driver to gently pry motor out. Snap in the new motor(the wiring was on the wrong side and the power cord coloring backwards on the replacement motor, but I snapped it in with the colors criss crossed and it worked). Re plug in the 3 plugs. Re mount mounting assembly, tray and then guard. Had a little trouble getting the tray back in. There is a little flap in the back that goes inside the tray. Other than that, a pretty easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Frisco, TX
- Parts Used:
- W11566405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Water was not circulating to the freeze area
Easy. I took a picture with everything in tact. Took apart a couple of parts with screw driver. Replaced the pump. Put it all together and it worked fine.Thanks.
Was this instruction helpful to you?
Thank you for voting!