Models > 10689582702

10689582702 Kenmore Ice Maker

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for 10689582702

Viewing 5 of 5
Keep searches simple, eg. "belt" or "pump".
$67.84
Used with stand-alone ice cube makers.
In Stock
Order within the next 7 hrs and your part ships today!
$75.62
This part monitors the temperature and sends the readings to the electronic control board.
In Stock
Order within the next 7 hrs and your part ships today!
This part controls the light.
In Stock
Order within the next 7 hrs and your part ships today!
This part is located in the water pump area of the ice cube maker.
On Order
$11.81
In Stock
Order within the next 7 hrs and your part ships today!
Used with free-standing ice cube makers.
In Stock
Order within the next 7 hrs and your part ships today!
This part includes the recirculation pump and motor sensor.
In Stock
Order within the next 7 hrs and your part ships today!
Screw size is 8-18 x 5/8". Used with stand-alone ice cube makers.
In Stock
Order within the next 7 hrs and your part ships today!
$5.36
This screw is sold individually.
In Stock
Order within the next 7 hrs and your part ships today!
Sold individually.
In Stock
Order within the next 7 hrs and your part ships today!
In Stock
Order within the next 7 hrs and your part ships today!
Sold individually.
On Order

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for 10689582702

Viewing 1 of 1
Light not working
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Randy from Hays, KS
Parts Used:
WP2149705
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Broken light switch
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'
77 of 128 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from North Wilkesboro, NC
Parts Used:
W11566405
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
was not making ice
diagnosed no water flow over evaporator checked voltage into pump then checked pump with ohm meter ordered pump and installed by removing access cover and water holding assembly installed new pump replaced water holding assembly and access cover and returned icemaker to service all is well
48 of 57 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ray from Terry, MS
Parts Used:
WPW10503764
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Ice maker overfilling with ice and would not stop production when full.
Very easy to replace. Down load the Manual online for a completely operating manual. Thermistor can be tested with an Ohm Meter. Proper values are listed in operating manual.
25 of 32 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!