10689583705 Kenmore Ice Maker - Instructions

The process to repair was very simple, I removed the back of the refrigerator to expose the motor area. I then removed three screws that held the condenser motor in place. once it was loose I detactched the electrical harness and removed the old motor. I then placed the new motor in place and secured it with the screws and reattached the new electrical harness that came with the new part. Once completed I reviewed it to make sure I didn't miss anything. I then replaced the cover over the motor area and enjoyed my success in repairing my own appliance with no added cost for labor, which would have been expensive I'm sure. The part purchased came with clear and consice instructions very easy to follow.

We have a side-by-side fridge/freezer and we experienced a hot center post (where doors come together) and the fridge made loud noise. Also, the (old) fan motor would start, but then quit, so our issue was the motor.

For me the repair was very easy, but for an unexperienced person it may prove to be difficult. If you must order a motor/fan, do NOT order the metal fan as a plastic fan comes with the motor. What's strange is the new motor is different than the old one, but it still mounted without any required modifications. I did NOT use the wire harness that came with the motor either as it was different too, but my old one was still good.

Check all of your parts as my fan had a cracked blade, but I used "superglue" and it's fine now.

Fridge stays cold and my wife had to lower the temperature in the fridge as she was blasted by the cold!

The procedure was straightforward. I removed the cardboard backing on the lower back of the refrigerator to expose the fan unit. I then undid the electrical harness at the fan. I then removed the three screws securing the fan motor to the metal bracket. This is the hardest part in that I had to reach through and get to the screws with my small tools. I then removed the old motor and blades and placed the new motor and blades. Again, a bit tricky trying to get the three screws mounted into the bracket...small tools and hands helps. After that I used the electrical harness supplied with the kit to plug into the new motor and I was done.

I removed the 2 screws on each side of the grid and disconnected the electrical plugs attached to the grid. I slid the broken unit out. I then carefully slid the new unit in making sure not to pinch any of the electrical wires. I replaced the mounting screws, plugged the 3 connectors back into place and turned the ice maker back on. I had ice cubes within a couple of hours

I removed the cutter grid and unplugged the light bulb and wire heating plug ins. I slid the front cover plate off the cutting grid and loosened the screws on the front of the cutter grid and unthreaded the broken, top grid wire, leaving the bottom wire in place as it was in tact.
I then threaded the new wire through the cutting grid frame starting in the center and threading right and then left. While the threading was not difficult, the wire was easily kinked. The process up to this point was only 15 minutes or so.

Once it was completely threaded, I worked for a couple of hours trying to smooth and straighten the wire so that is was somewhat taut and straight enough to create symetrical ice cubes.
My frustration came in pulling on the wire from the center point to each outside ending point where it was to be wrapped around the screw and the screw tightened back down. The wire was fragile enough that it would break, by the time I was finished I barely had enough wire left to touch the screw let alone hook around the screw.
After 3 or four days of successful opperation, the grid quit cutting again. As I took it apart, it was obvious that the weight of the ice was enough to pull the wire, that was already too short, away from the screw. I refastened it again, but think it is unlikely to hold.
If it won't hold, I would be hard pressed to purchase another wire. I may bite the bullet and purchase the entire grid mechanism with the wires already installed. Even though the cost of the entire grid mechanism is $200 more than the purchase of another wire, it may well be worth the ease of installation!

removed the clip that the motor was attached too put the new motor back on reinstalled the clip back on the fridge plugged the wire harness in and works perfect now . it was easier to remove the clip than to try to install the motor by itself its just to tight and you cant get in there

First I removed the cutter grid assembly by removing two screws. Also disconnect the wire that powers the grid. Once on the bench, simply remove the broken cutter wire. String in the new wire, starting at one end and working back and forth to the other end. Tighten the terminal screw on the first end, and then "strum" the wires, one at a times, pulling the wires taught. Pull the excess wire thru the second terminal, until all wires are taught, with equal tension. Tighten the second terminal screw, and cut off excess wire at both ends. Re-assemble cutter grid into Ice Maker.
Problem solved!

I removed 4 screws holding the motor mounting bracket and removed the assy from the unit. I then removed 3 screws holding the motor to the bracket. I put the fan blade on the new motor and reattached the motor to the bracket. I plugged in the wiring adapter to the motor and reinstalled the bracket in the unit with the 4 screws. Finally I attached the unit wiring connector to the motor.
It was relatively easy.

Followed instructions in owner's manual, which are also on the bottle of cleaner we ordered. Very easy to use. Only had to take ice out of bin, and cut ice maker off, then add the cleaner to the water pan, and press button to clean. It was very easy, and effective. The buildup of stain, etc. was removed completely. We just had to turn the icemaker back on, and allow time for ice to begin filling the bin.
Thanks very much.

Replaced the entire unit (fan and motor). Would have rated this repair as "Really Easy", but found it a little difficult because of large hands.

There was a loud noise coming from the fridge - we ordered the new part it came a lot sooner than we excepted and we replaced it in about 20 minutes- the hardest part was my husband getting his hand in there to put the screws in- but a very easy fix.

remove tray from icemaker by removing 2 screws and disconnecting 2 electrical connectiona. Remove broken wire and restring new wire. Reinstall tray.

Removed the grid. Removed the existing top to bottom wire. Restrung the grid with the new wire. Then, it cut ice just fine-better than new. Note: wire provided is only sufficient to rewire side to side or top to bottom, not both. If you need to do both, you'll need 2. Yes, lots of money for a few feet of wire.

r&r fan blade and motor. with the parts you supplied it was easy. the parts were perrrrfect. thank you very much. job well done. bruce

The post I read said start at the middle and work your way out towards the left and right. This was incorrect. All I did was secure one end to the torx screw and tighten it down. I then slowly pulled the wire as tight as I could around each insulator, going slow so as to not kink the wire (very easy to do). Once I was at the other torx screw I used a pair of linesman plyers to gently tug each wire tighter, I needed an extra pair of hands to hold the grid down. Once everything was tight I wrapped the last torx screw and tightened. Here's what no one is saying, you will not get the wire as tight as it originally was but that's ok. After I got everything reinstalled the ice maker is making ice like a champ.