Models
>
59689599101
59689599101 Kenmore Ice Maker
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
This temperature sensor monitors the ice bin in select refrigerators to help regulate ice production. It sends temperature readings to the control board, preventing overfilling or melting. Compatible ...
In Stock
Order now and your part arrives by Apr 23
In Stock
Order now and your part arrives by Apr 23
The water distributor tube distributes water from the reservoir to the evaporator plate.
In Stock
Order now and your part arrives by Apr 23
In Stock
Order now and your part arrives by Apr 23
In Stock
Order now and your part arrives by Apr 23
In Stock
Order now and your part arrives by Apr 23
In Stock
Order now and your part arrives by Apr 23
$160.08
This cutter grid uses heated wires to cut ice slabs into uniform cubes before they drop into the bin. It helps improve ice maker efficiency and consistency. If your ice cubes are misshaped or not bein...
In Stock
Order now and your part arrives by Apr 23
In Stock
Order now and your part arrives by Apr 23
Special Order
In Stock
Order now and your part arrives by Apr 23
$45.00
This filter dryer is for refrigerators and filters refrigerant that travels through the sealed system of the refrigerator.
In Stock
Order now and your part arrives by Apr 23
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Travis from N CHESTERFLD, VA
- Parts Used:
- WPW10511923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice bin overfilling
I'm an hvac/r technician, and regularly work on ice machines. Begin my pulling the white over beneath the control panel. It snaps in place so pull on the bottom then left out. 1/4 nut driver is all you need, and remove the screw holding the bin thermistor clip to the side. Up to the right , beneath the control panel, behind the plasti
... Read more
c panel you previously removed is the mollex connector. Unplug the thermistor and follow instructions in reverse to reinstall.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from etowah, TN
- Parts Used:
- W10881366
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Ice maker started leaking water from the water valve that inputs water to the appliance.
removed the front cover below the compartment door,removed the 2 screws holding the valve to the case and removed the water lines from the valve.The process was reversed to install the new valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from LITITZ, PA
- Parts Used:
- WPW10511923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Ice bin overflowing not shutting off. Kept making ice
Pull cover off in front of ice tray and ice grid cutter to make easy to get at temperature sensor wire connector. remove connection plug to temperature sensor remove screw on side of ice bin that holds sensor in position.
Put sensor in a class of ice 32 degrees and measured resistance read 6.2K should of been read 8.7K Ordered a ... Read more new Temperature sensor from partselect.com . Installed in 5 min working like a champ again.
The instructions book call the part I need a Bin Thermister instead off temperature sensor.
Put sensor in a class of ice 32 degrees and measured resistance read 6.2K should of been read 8.7K Ordered a ... Read more new Temperature sensor from partselect.com . Installed in 5 min working like a champ again.
The instructions book call the part I need a Bin Thermister instead off temperature sensor.
Read less
Was this instruction helpful to you?
Thank you for voting!