Models
>
DLL2580PC
DLL2580PC Hotpoint Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$49.67
Be very careful to not handle the igniter by its gray part. Hold it by its white tip only.
In Stock
$348.87
Replaces "T" and "V" style motors. Includes two motor pulleys. If you have an older model dryer, the pulley may be pressed on or held on with a set screw. If pulley is pressed on, a new motor pulley must be ordered.
In Stock
This part has three terminals. Note: Use the two smaller terminals for models that only have two wires to the switch.
No Longer Available
In Stock
This dryer drum belt goes around the dryer drum and the pulleys to rotate the drum once motor is activate.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for DLL2580PC
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeff from Seattle, WA
- Parts Used:
- WE4X444
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Gas dryer heat would not come on
Unplugged dryer, opened lower panel. Loosened the bolt that holds igniter assembly to gas unit and removed old igniter. Put new igniter in the pinch clamp then (being VERY careful so as not to crack new part) replaced igniter assembly and tightened its bolt firmly. Voilà, ignition!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Virginia Beach, VA
- Parts Used:
- WE4X197
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replqce bad switch
pried old switch assembly from front of machine with screw driver. removed 2 electrical connections. shorted terminals to verify problem. inserted wiring terminals to new switch. verified operation and then pushed switch assembly into machine opening.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anton from saint charles, IL
- Parts Used:
- WE4X444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
no ignition
1. remove the access door , bottom left side
2. unplug the power cord and shut the gas valve off, next to the union fitting
3. unplug the electrical connections from the gas valves and igniter.
4. open the union with the wrench, right hand thread
5. remove the two nut driver screws on the burner lip
6. remove the ... Read more burner and carefully spread the igniter fingers and remove the igniter
7. check the igniter, make sure it is the problem.
8. install the new igniter and carefully insert the burner into position.
9. reverse the disassembly , turn on the gas valve and check for leaks with soap bubbles. if you have a leak, shut off the gas valve and repair it or leave the gas valve off and call a repairman.
10. plug in the power and turn on the dryer the igniter should glow white hot and the burner should light.
11. if the dryer does not work you have other problems or you did not plug the electrical connections into the correct places,
12. call the repairman or buy a new dryer
2. unplug the power cord and shut the gas valve off, next to the union fitting
3. unplug the electrical connections from the gas valves and igniter.
4. open the union with the wrench, right hand thread
5. remove the two nut driver screws on the burner lip
6. remove the ... Read more burner and carefully spread the igniter fingers and remove the igniter
7. check the igniter, make sure it is the problem.
8. install the new igniter and carefully insert the burner into position.
9. reverse the disassembly , turn on the gas valve and check for leaks with soap bubbles. if you have a leak, shut off the gas valve and repair it or leave the gas valve off and call a repairman.
10. plug in the power and turn on the dryer the igniter should glow white hot and the burner should light.
11. if the dryer does not work you have other problems or you did not plug the electrical connections into the correct places,
12. call the repairman or buy a new dryer
Read less
Was this instruction helpful to you?
Thank you for voting!