1149-0-580327112 Craftsman Generator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from PICAYUNE, MS
- Parts Used:
- 192980GS
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from RADFORD, VA
- Parts Used:
- 192980GS
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Was this instruction helpful to you?
Thank you for voting!
Gas tank leaking, pull starter rivets worn, rope and rope bushing worn
The gas tank was a simple job, close the fuel shut off, remove fuel hose then back out 2 bolts on the mounting bracket. Reverse procedure to mount.
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill switch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill switch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from LEES SUMMIT, MO
- Parts Used:
- 192980GS
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alberto from PALMETTO BAY, FL
- Parts Used:
- 692237
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Generator would not start, Birggs & Stratton recommended to replase Gasket Exhaust.
Remove the spark suppresser, 4 face screws, 2 bottom screws and the two screws the hold the gasket. I also had to back out the top screw of the cover it blocked and prevented the removal of the gasket.
Was this instruction helpful to you?
Thank you for voting!