Models
>
1188-0-580327130
1188-0-580327130 Craftsman Generator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Nov 12
$24.05
This fuel valve with bushing fits a variety of outdoor equipment and allows the fuel to smoothly flow into the gas engine. The bushing part is pressed into the hole provided in the fuel tank and the f...
In Stock
Order now and your part arrives by Nov 12
It is a genuine item that is supplied directly from the original equipment manufacturer for use with Generac portable generators. The bolt helps to secure the cover. This is a high-quality replacement...
In Stock
Order now and your part arrives by Nov 12
$6.51
This is an authentic replacement part that has been sourced from the original manufacturer to be used with generators and pressure washers. The foam filter is the pre-filter that is used to prevent fi...
In Stock
Order now and your part arrives by Nov 12
$6.51
This spark plug is designed to provide reliable ignition and efficient fuel combustion in small engine applications. Built for consistent performance and durability, it helps maintain smooth operation...
On Order
This is an authentic Generac replacement part that has been sourced from the original manufacturer to be used with generator engines. The recoil starter is a complete part assembly that includes the h...
In Stock
Order now and your part arrives by Nov 12
$51.65
This is an authentic OEM sourced part which is designed for Briggs and Stratton and Snapper generators. It is an important part that keeps the fuel in the tank and the gauge shows a user the level of ...
In Stock
Order now and your part arrives by Nov 12
It is a genuine replacement part that is supplied by the original manufacturer for use with Generac generators. This is the special gasket that is utilized to provide an air-tight seal for the manifol...
In Stock
Order now and your part arrives by Nov 12
$14.77
This is an original replacement part sourced directly from the manufacturer. The rocker arm is found in Generac generators. This part is made of metal, and is attached to the push rod guide plate in...
In Stock
Order now and your part arrives by Nov 12
$17.84
This is an authentic OEM component from Generac. The carburetor/air box gasket is made for use with several generator engines. The cardboard composite gasket is fitted between the carburetor and air c...
In Stock
Order now and your part arrives by Nov 12
$175.63
This is an authentic replacement part sourced directly from the manufacturer. The carburetor is found in generators from Generac. This part is a complete carburetor assembly, which is used to mix fu...
In Stock
Order now and your part arrives by Nov 12
In Stock
Order now and your part arrives by Nov 12
Common Problems and Symptoms for 1188-0-580327130
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from PICAYUNE, MS
- Parts Used:
- 192980GS
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from RADFORD, VA
- Parts Used:
- 192980GS
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from LEES SUMMIT, MO
- Parts Used:
- 192980GS
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Was this instruction helpful to you?
Thank you for voting!