Models
>
030201-0
030201-0 Briggs and Stratton Generator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 030201-0
Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
$26.70
This fuel valve with bushing fits a variety of outdoor equipment and allows the fuel to smoothly flow into the gas engine. The bushing part is pressed into the hole provided in the fuel tank and the f...
In Stock
Order now and your part arrives by Mar 22
$56.96
This is an authentic OEM sourced part which is designed for Briggs and Stratton and Snapper generators. It is an important part that keeps the fuel in the tank and the gauge shows a user the level of ...
On Order
$16.16
An authentic OEM replacement fuel line that is specially produced for use with gas powered endings commonly installed on generators and other equipment. The fuel line is used to deliver the fuel from ...
On Order
$138.22
This authentic replacement part is specially designed for Briggs and Stratton generators. It is supplied from the original equipment manufacturer. This is an important component of the unit which regu...
In Stock
Order now and your part arrives by Mar 22
$31.80
This is a brush holder assembly for your generator. Brushes conduct electric currents to provide power in the motor of your unit. The brush assembly is mounted into a bearing carrier, and is wired to ...
On Order
$110.86
This is an authentic manufacturer made replacement part which is specially designed for use with Craftsman pressure washers. The wheels are attached to the bottom of the pressure washer and are used f...
In Stock
Order now and your part arrives by Mar 22
In Stock
Order now and your part arrives by Mar 22
$6.57
Keep in mind that this high-quality part is made of metal and is sold individually. A set of pliers might be helpful during the installation of this part. The e-ring fits onto the wheel and will need ...
In Stock
Order now and your part arrives by Mar 22
In Stock
Order now and your part arrives by Mar 22
In Stock
Order now and your part arrives by Mar 22
In Stock
Order now and your part arrives by Mar 22
This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cov...
In Stock
Order now and your part arrives by Mar 22
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 030201-0
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from PICAYUNE, MS
- Parts Used:
- 192980GS
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from RADFORD, VA
- Parts Used:
- 192980GS
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from LEES SUMMIT, MO
- Parts Used:
- 192980GS
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Was this instruction helpful to you?
Thank you for voting!