Models
>
01815
01815 Briggs and Stratton Generator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 01815
Viewing 5 of 5Keep searches simple, eg. "belt" or "pump".
In Stock
In Stock
In Stock
In Stock
In Stock
Special Order
In Stock
In Stock
In Stock
In Stock
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bobbie
March 10, 2023
Generator runs for about 5-7 mins then shuts down error code pops up engine failed to start
For model number 01815
Hello Bobbie, Thank you for your inquiry. This is usually caused by an issue with the fuel system of the engine. Since the engine parts are listed separately under the engine's model number, we would need the model number and type code of the engine in order to find the correct parts and repair information. The model number and type code should be on a sticker or stamped into the front or side of the engine. We look forward to hearing from you.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Larry
March 6, 2024
Generator will start. Run approximately 3 to 5 minutes. Starter appears to try and engage. Shuts down. Starter is good. Solenoid?
For model number 01815
Hi Larry, thank you for getting in touch. Based on the description, the issue is probably with the starter solenoid, part number FIX9064363. It engages and routes the battery electrical supply to the engine starter when the ignition switch is rotated to the start position. You may need to replace it to fix the issue. We hope this sorts out your problem!
Was this helpful?
Thank you for voting!
Related Parts:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bruce from CARNATION, WA
- Parts Used:
- 691656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Wouldn’t start.
I installed a new solenoid starter. Took me a total of 20 minutes. Started right up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laron from GRAND RAPIDS, MI
- Parts Used:
- 192366GS
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No voltage on secondary side of transformer. Confirmed with meter that transformer windings had infinite resistance.
1. Turn the generator selector switch to "OFF"
2. Remove the 240 volt fuses in the automatic transfer switch to remove power to the transformer.
3. Remove the outside cover from the front of the generator, on the motor end.
4. Remove the 3 screws from the panel covering the controls.
5. Label or make note of which ... Read more terminals the 4 wires on the transformer go to and disconnect from transformer.
6. Using 9/32 nutdriver, remove the two transformer mounting nuts and lock washers.
7. Remove old transformer from studs and install new one. Reinstall nuts and lock washers.
8. Reconnect the 4 transformer wires.
9. Reinstall the control panel cover and the generator housing end cover.
10. Reinstall the fuses in the automatic transfer switch.
11. Put the generator selector switch back in "Automatic"
2. Remove the 240 volt fuses in the automatic transfer switch to remove power to the transformer.
3. Remove the outside cover from the front of the generator, on the motor end.
4. Remove the 3 screws from the panel covering the controls.
5. Label or make note of which ... Read more terminals the 4 wires on the transformer go to and disconnect from transformer.
6. Using 9/32 nutdriver, remove the two transformer mounting nuts and lock washers.
7. Remove old transformer from studs and install new one. Reinstall nuts and lock washers.
8. Reconnect the 4 transformer wires.
9. Reinstall the control panel cover and the generator housing end cover.
10. Reinstall the fuses in the automatic transfer switch.
11. Put the generator selector switch back in "Automatic"
Read less
Was this instruction helpful to you?
Thank you for voting!