Models
>
1306-0-PP5000T
1306-0-PP5000T Briggs and Stratton Generator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$6.25
This is a hair pin clip for your lawn equipment. You may also know it as a cotter pin. It is a multi-application part, depending on your unit, as well as the make and model. To correctly install the p...
In Stock
Order now and your part arrives by Mar 21
$26.70
This fuel valve with bushing fits a variety of outdoor equipment and allows the fuel to smoothly flow into the gas engine. The bushing part is pressed into the hole provided in the fuel tank and the f...
In Stock
Order now and your part arrives by Mar 21
$15.10
This part is an original part from Briggs & Stratton and Snapper for use in generators and welders. The circuit breaker goes inside the control box and helps to control electricity flow. A screwdriver...
Special Order
$6.25
This is an authentic OEM part from Briggs and Stratton and Snapper for use with Generators. The fuel tank mounting grommet forms a cushion between the fuel tank and the fuel tank mounting bolts. The m...
In Stock
Order now and your part arrives by Mar 21
$33.32
This is a genuine manufacturer-sourced replacement wheel which is specially designed for use with Briggs and Stratton and Snapper generators. It is an identical replacement for a missing or damaged wh...
In Stock
Order now and your part arrives by Mar 21
This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cov...
In Stock
Order now and your part arrives by Mar 21
$6.25
This replacement flange nut is an authentic manufacturer-sourced component which is specially designed for use with Briggs and Stratton equipment. It is the hardware which has multiple applications de...
In Stock
Order now and your part arrives by Mar 21
$34.35
This item is available as an individual replacement part. The outlet is made out of metal and plastic. It may require a wrench during installation. This item will need to be replaced if it breaks. It ...
In Stock
Order now and your part arrives by Mar 21
Special Order
$47.27
This is an authentic Briggs & Stratton replacement part. The bearing is commonly found in generators. This part is made of metal, and is used to allow the rotor assembly to spin freely within the st...
Special Order
$17.12
This item has been sourced from the original manufacturer to be used with portable generators from Briggs & Stratton. The metal and rubber mount is used to support the motor. This item absorbs vibrati...
In Stock
Order now and your part arrives by Mar 21
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 1306-0-PP5000T
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from PICAYUNE, MS
- Parts Used:
- 192980GS
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from RADFORD, VA
- Parts Used:
- 192980GS
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from LEES SUMMIT, MO
- Parts Used:
- 192980GS
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Was this instruction helpful to you?
Thank you for voting!