Models
>
GFWS1505D0MP
GFWS1505D0MP General Electric Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GFWS1505D0MP
Viewing 5 of 5Keep searches simple, eg. "belt" or "pump".
In Stock
In Stock
In Stock
This part is the replacement door plunger or door strike for your washer. It is made of white plastic and is approximately 2 inches by 1.5 inches. The door strike attaches to the washer door and activ...
No Longer Available
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
On Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for GFWS1505D0MP
Viewing 4 of 4Leaking
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Dallas, PA
- Parts Used:
- WH10X10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
"Door Locked" light always on. Washer would not run
Remove bottom kick plate of washer. Remove 4 screws behind door that hold the latch/lock assembly. Reach up inside the washer from underneath to unplug 3 wire connectors. (This is a very tight spot). Once wires are off, part comes right out. Connect wires to the new part - this is by far the most difficult part of the job because it
... Read more
is way up inside the washer. Replace all bolts.
Overall, pretty easy to do - just reconnecting the wires is a pain, but if you are patient it is not a big deal.
Overall, pretty easy to do - just reconnecting the wires is a pain, but if you are patient it is not a big deal.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Spring Branch, TX
- Parts Used:
- WH01X10356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door plunger broken so could not lock.
Part came quickly, was exactly what I needed, 2 minutes later, washing clothes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from HARRIMAN, TN
- Parts Used:
- WH11X34740
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer stopped during wash cycle and wouldn't open.
Removed three 7mm sheet metal screws from the bottom front panel.
The drain pump is in the front right.
Removed the manual drain screen to drain residual water from the system. A bucket was necessary to collect all the water.
Disconnected the inlet and outlet hose.
Disconnected the electric supply.
Removed two Phi ... Read more llips screws holding the pump to the bottom of the machine.
Slid the pump towards the rear to clear the support pegs and removed it from the front opening.
Installation is the reverse of those steps.
The drain pump is in the front right.
Removed the manual drain screen to drain residual water from the system. A bucket was necessary to collect all the water.
Disconnected the inlet and outlet hose.
Disconnected the electric supply.
Removed two Phi ... Read more llips screws holding the pump to the bottom of the machine.
Slid the pump towards the rear to clear the support pegs and removed it from the front opening.
Installation is the reverse of those steps.
Read less
Was this instruction helpful to you?
Thank you for voting!