Models
>
PSB9100SF2SS
PSB9100SF2SS General Electric Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for PSB9100SF2SS
Viewing 5 of 5
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Apr 10
This is a control knob for your microwave. The knob is about 1.5 inches in diameter, is black and silver in color, and is sourced directly from the original manufacturer.
No Longer Available
$39.63
This diode cable is a replacement electrical component designed to regulate current flow within an appliance circuit. It helps protect sensitive components and is commonly replaced when electrical fau...
In Stock
Order now and your part arrives by Apr 10
In Stock
Order now and your part arrives by Apr 10
$187.39
Genuine OEM magnetron for your microwave. Always use proper safety equipment and follow the manufacturers instructions while installing.
In Stock
Order now and your part arrives by Apr 10
In Stock
Order now and your part arrives by Apr 10
$35.34
This part will trip once the inside of the cavity overheats and exceeds the recommended temperature.
In Stock
Order now and your part arrives by Apr 10
$55.18
This capacitor delivers the electrical boost required for motors to start and operate efficiently. Proper capacitance reduces strain on motor components and helps prevent startup failures or inconsist...
In Stock
Order now and your part arrives by Apr 10
In Stock
Order now and your part arrives by Apr 10
In Stock
Order now and your part arrives by Apr 10
In Stock
Order now and your part arrives by Apr 10
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for PSB9100SF2SS
Viewing 2 of 2
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Coulterville, CA
- Parts Used:
- WB21X10148, WB26X32629
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No power to microwave, no heating.
Unpluged power cord!! Removed front control panel to expose electronics (need to remove top horizontal vent cover to expose mounting hardware). Unplugged leads to control panel board. Removed magnetron with Tstat (3- phillip heads, need stubby). Installed new parts and control panel, plugged it in tested. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Dayton, NV
- Parts Used:
- WB27X10037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Microwave would not heat food
First and most important - unplug AC power 24 hours before service.
I removed the vent cover above the main door, then I removed the screw which holds the control panel in place, unplugged the main connector on the control panel so I would have enough room to work, removed grounding screw from the DIODE ASSY, pulled connector o ... Read more ff the CAPACITOR with pliers, installed new DIODE ASSY.
After installation of DIODE and the control Panel, I plugged in the AC power and allowed the CAPACITOR to charge - this takes about an hour or so, then test. Works perfect!
I removed the vent cover above the main door, then I removed the screw which holds the control panel in place, unplugged the main connector on the control panel so I would have enough room to work, removed grounding screw from the DIODE ASSY, pulled connector o ... Read more ff the CAPACITOR with pliers, installed new DIODE ASSY.
After installation of DIODE and the control Panel, I plugged in the AC power and allowed the CAPACITOR to charge - this takes about an hour or so, then test. Works perfect!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michelle from virginia beach, VA
- Parts Used:
- WB20X10048
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Original part was fried
Had to remove microwave from the wall. Then disassemble entire top assembly to get to the part. Easy enough to replace after that. Then just reassemble and reinstall. About 2hrs. total
Was this instruction helpful to you?
Thank you for voting!