Models
>
JVM1653WH06
JVM1653WH06 General Electric Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JVM1653WH06
Viewing 8 of 8
Manuals & Guides for JVM1653WH06
Click to downloadKeep searches simple, eg. "belt" or "pump".
$20.72
This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the micro...
In Stock
Order now and your part arrives by Apr 12
$52.50
This replacement microwave grease filter features multiple layers of aluminum that work together to capture grease and minimize odors. By preventing debris from entering the recirculation system, it h...
In Stock
Order now and your part arrives by Apr 12
In Stock
Order now and your part arrives by Apr 12
In Stock
Order now and your part arrives by Apr 12
In Stock
Order now and your part arrives by Apr 12
$15.26
This is the replacement damper bracket for your microwave. It is made of plastic and is approximately 11 inches wide and 3 inches long. The damper bracket attaches to the outer cabinet and directs air...
In Stock
Order now and your part arrives by Apr 12
$24.00
This mounting plate, also known as a bracket, is crucial for keeping your microwave mounted to the wall, when placed above the stove. This OEM part is sold separately from the screws that are needed t...
In Stock
Order now and your part arrives by Apr 12
$15.26
This part is the replacement high-voltage diode for your microwave. It is approximately 3 inches long and is sold individually. The high voltage diode is an electrical current control device inside yo...
In Stock
Order now and your part arrives by Apr 12
In Stock
Order now and your part arrives by Apr 12
$37.49
This switch monitor interlock helps your microwave detect when the door is properly closed. If it’s damaged, the microwave may not start. Replacing it restores safe operation and is a quick fix with basic tools.
In Stock
Order now and your part arrives by Apr 12
This vent grille mounts on the top of the microwave above the door.NOTE*** Part is only available in white.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JVM1653WH06
Viewing 6 of 6No heat
Fixed by these parts
How to fix it
Won’t turn on
Fixed by these parts
How to fix it
Door not closing properly
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Doesn’t shut off
Fixed by these parts
How to fix it
Tray won’t turn
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kim from Cliffside Park, NJ
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave completely stopped working
Turned out the issue was easily solved by replacing a single, inexpensive fuse.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic ... Read more rowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic ... Read more rowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Brandon, FL
- Parts Used:
- WB27X10928
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
I diagnosed the problem incorrectly: based on a previous repair.
The old fuse is perfectly good. The new ones arrived within a day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Austn, TX
- Parts Used:
- WB55X10828, WB07X10968
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The door panel and grille vent are plastic and thay both cracked and fell apart due to cheap plastic parts from GE.
Removed the screws at the top of vent and took the vent off and then removed the door by lifting it off the hinge. I had to break the old plastic door frame to get it off, but since it was no good anyway it didnt matter. Then I put the glass in the new frame put the handle on it and snapped the frame on to the door and put it back on t
... Read more
he door hinge and then put the new vent on and screwed it down and closed the door. Job was not to hard at all.
Read less
Was this instruction helpful to you?
Thank you for voting!