Models
>
DCSR483GA2WW
DCSR483GA2WW General Electric Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for DCSR483GA2WW
Viewing 6 of 6
Manuals & Guides for DCSR483GA2WW
Click to downloadKeep searches simple, eg. "belt" or "pump".
This single drum bearing slide attaches to the outer-most side of the bearing. This part is also sometimes referred to as a drum slide, drum glide, or drum pad. It provides support to the front of the...
In Stock
Order now and your part arrives by Apr 9
$25.10
This is a genuine OEM replacement timer knob for your dryer. It is made of white plastic, and includes the metal clip that fits onto a D-shaped shaft. Replacing this part is an easy repair, simply pul...
In Stock
Order now and your part arrives by Apr 9
In Stock
Order now and your part arrives by Apr 9
$36.42
This is a timer knob for your dryer. It is found on the control panel and allows you to turn your dryer on and adjust the settings. If the timer will not advance, or you notice the knob is damaged, yo...
In Stock
Order now and your part arrives by Apr 9
$31.05
This rear drum bearing sleeve supports the dryer drum and helps it rotate smoothly. It’s a common fix for noisy dryers or drums that wobble or stop turning. Compatible with select GE and Hotpoint mode...
In Stock
Order now and your part arrives by Apr 9
$17.58
This is a replacement O-ring for the drum bearing retainer on your dryer. The drum bearing is found at the back of the dryer drum. The O-ring is designed to create a seal on the drum bearing. The O-r...
In Stock
Order now and your part arrives by Apr 9
$37.49
A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.
In Stock
Order now and your part arrives by Apr 9
This conversion kit changes the dryer from natural gas to liquid propane. Installation instructions are included.
In Stock
Order now and your part arrives by Apr 9
In Stock
Order now and your part arrives by Apr 9
In Stock
Order now and your part arrives by Apr 9
In Stock
Order now and your part arrives by Apr 9
$79.09
This white dryer access panel covers and protects the top of the dryer cabinet while providing a clean, finished appearance. Made from durable metal, it is commonly used to replace panels that are scr...
In Stock
Order now and your part arrives by Apr 9
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for DCSR483GA2WW
Viewing 6 of 6Noisy
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- SAM from ROCK HILL, NY
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced broken START knob on dryer.
Slid off the old START knob, then pushed on the new START knob.
I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.
I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the ... Read more time selector dial.
My teenage daughter was not setting the time selector dial, to a point past 10 minutes. When she turned the START knob, the dryer would not come on, because the time selector dial was not set past the 10 minute setting.
My daughter had continually twisted the START knob until it broke. I am hoping she will be able to see the large printed label I put on the dryer near the time selector, saying "Minimum" with a large red arrow pointing past 10 minutes.
I am very pleased that I was quickly able to find the exact matching START knob for my dryer and the exact same color, from PartSelect.Com
I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.
I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the ... Read more time selector dial.
My teenage daughter was not setting the time selector dial, to a point past 10 minutes. When she turned the START knob, the dryer would not come on, because the time selector dial was not set past the 10 minute setting.
My daughter had continually twisted the START knob until it broke. I am hoping she will be able to see the large printed label I put on the dryer near the time selector, saying "Minimum" with a large red arrow pointing past 10 minutes.
I am very pleased that I was quickly able to find the exact matching START knob for my dryer and the exact same color, from PartSelect.Com
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Irvine, CA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The inside of the Selector Knob was stripped
Removed the damaged knob and replaced it with the new knob. Very ease
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from North Richland Hills, TX
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer door handle broke off.
I pried out the remaining pieces of the handle out of the door with a screwdriver. When the new part arrived, I snapped it into place and it was done. It fit perfectly.
Was this instruction helpful to you?
Thank you for voting!