Models
>
FHWC3050RSA
FHWC3050RSA Frigidaire Range Hood
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for FHWC3050RSA
Viewing 2 of 2
Manuals & Guides for FHWC3050RSA
Click to downloadInstall
Installation Instructions
(4.59MB)
Manual
Owner's Manuals
(5.28MB)
Wiring
Wiring Diagram
(0.13MB)
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Apr 6
Special Order
In Stock
Order now and your part arrives by Apr 6
Special Order
Special Order
Special Order
Special Order
Special Order
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- RICH from Leland, NC
- Parts Used:
- 5304504588, 5304504587
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
BROKEN KNOB ASSEMBLYS
REMOVAL
1 ) POWER SWITCH ASSY DOWN AT BREAKER BOX
2 ) LOWER FILTER COVER BY PRESSING FRONT CORNERS, LET HANG
3 ) REMOVE FILTERS
4 ) UNSCREW 2 #2 PHILLIPS HEAD SCREWS LOCATED AT THE REAR OF THE PANEL HOLDING PANEL TO HOOD BODY
5 ) SLIDE PANEL TO THE REAR TO DISENGAGE
6 ) REMOVE SELECTOR KNOBS FROM KNOB AS ... Read more SY (EXTEND KNOBS AND WIGGLE FREE)
7 ) REMOVE 2 #1 PHILLIPS HEAD SCREWS HOLDING KNOB ASSY TO SWITCH ASSY, LOCATED INSIDE KNOB ASSY
8 ) UNSCREW THREADED SLEEVE ON KNOB ASSY
9 ) REMOVE KNOB ASSY
INSTALLATION
1 ) DISASSEMBLE NEW PART INTO COMPONENT PIECES
2 ) SLIDE RETAINER PORTION OF KNOB ASSEMBLY THROUGH APPROPRIATE HOLE IN PANEL
3 ) SCREW THREADED SLEEVE ONTO RETAINER
4 ) ATTACH KNOB ASSY TO SWITCH ASSY USING 2 # 1 PHILLIPS SCREWS
5 ) INSERT SELECTOR KNOBS INTO KNOB ASSY, MAKE SURE THAT THE MARKED (LIGHT OR FAN) KNOB CORRESPONDS TO THE CORRECT SWITCH
6 ) INSERT TABS ON FRONT OF PANEL INTO HOOD BODY
7 ) INSERT 2 #2 PHILLIPS SCREWS INTO REAR OF PANEL TO ATTACH TO HOOD BODY
8 ) REINSERT FILTERS
9 ) RAISE AND SECURE FILTER COVER
10) POWER BREAKER BACK ON
RECOMMEND TEST AFTER INITIAL ASSEMBLY BETWEEN STEPS 5 AND 6. GOOD LUCK
1 ) POWER SWITCH ASSY DOWN AT BREAKER BOX
2 ) LOWER FILTER COVER BY PRESSING FRONT CORNERS, LET HANG
3 ) REMOVE FILTERS
4 ) UNSCREW 2 #2 PHILLIPS HEAD SCREWS LOCATED AT THE REAR OF THE PANEL HOLDING PANEL TO HOOD BODY
5 ) SLIDE PANEL TO THE REAR TO DISENGAGE
6 ) REMOVE SELECTOR KNOBS FROM KNOB AS ... Read more SY (EXTEND KNOBS AND WIGGLE FREE)
7 ) REMOVE 2 #1 PHILLIPS HEAD SCREWS HOLDING KNOB ASSY TO SWITCH ASSY, LOCATED INSIDE KNOB ASSY
8 ) UNSCREW THREADED SLEEVE ON KNOB ASSY
9 ) REMOVE KNOB ASSY
INSTALLATION
1 ) DISASSEMBLE NEW PART INTO COMPONENT PIECES
2 ) SLIDE RETAINER PORTION OF KNOB ASSEMBLY THROUGH APPROPRIATE HOLE IN PANEL
3 ) SCREW THREADED SLEEVE ONTO RETAINER
4 ) ATTACH KNOB ASSY TO SWITCH ASSY USING 2 # 1 PHILLIPS SCREWS
5 ) INSERT SELECTOR KNOBS INTO KNOB ASSY, MAKE SURE THAT THE MARKED (LIGHT OR FAN) KNOB CORRESPONDS TO THE CORRECT SWITCH
6 ) INSERT TABS ON FRONT OF PANEL INTO HOOD BODY
7 ) INSERT 2 #2 PHILLIPS SCREWS INTO REAR OF PANEL TO ATTACH TO HOOD BODY
8 ) REINSERT FILTERS
9 ) RAISE AND SECURE FILTER COVER
10) POWER BREAKER BACK ON
RECOMMEND TEST AFTER INITIAL ASSEMBLY BETWEEN STEPS 5 AND 6. GOOD LUCK
Read less
Was this instruction helpful to you?
Thank you for voting!