Models
>
MZF34X18FW01
MZF34X18FW01 Whirlpool Freezer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for MZF34X18FW01
Viewing 6 of 6Keep searches simple, eg. "belt" or "pump".
$21.82
This is a screw and it is made for multiple appliances in your home. This model is called a sheet metal screw because it has sharp points, and the threads are closer together. This screw is designed t...
On Order
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
No Longer Available
In Stock
Order now and your part arrives by Nov 21
$28.91
The white, four-blade OEM evaporator fan blade moves cold air over your refrigerators evaporator coils. A noisy fan or a warm refrigerator can indicate a problem with the blade. Check your refrigerato...
In Stock
Order now and your part arrives by Nov 21
This temperature sensor is for refrigerators.
The temperature sensor senses the temperature inside the refrigerator and sends information to the electronic control.
Unplug the refrigerator and s...
In Stock
Order now and your part arrives by Nov 21
In Stock
Order now and your part arrives by Nov 21
$63.68
The compressor run capacitor is a crucial component for refrigerators, designed to help maintain the motor's operation. This genuine OEM replacement part is compatible with various refrigerator models...
In Stock
Order now and your part arrives by Nov 21
If your refrigerator runs too warm or too cold, or develops frost buildup, its thermistor may need replacement. This OEM part senses refrigerator air temperature for temperature control. Confirm compa...
In Stock
Order now and your part arrives by Nov 21
$68.99
This coated wire shelf adds extra storage space to your freezer and helps improve airflow. Its shallow design makes it ideal for organizing smaller items and can be easily repositioned to fit your needs.
In Stock
Order now and your part arrives by Nov 21
In Stock
Order now and your part arrives by Nov 21
Common Problems and Symptoms for MZF34X18FW01
Viewing 12 of 12Fridge too warm
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Frost buildup
Fixed by these parts
How to fix it
Freezer not defrosting
Fixed by these parts
How to fix it
Too warm
Fixed by these parts
How to fix it
Fridge and Freezer are too warm
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Door won’t open or close
Fixed by these parts
How to fix it
Fridge too cold
Fixed by these parts
How to fix it
Freezer section too warm
Fixed by these parts
How to fix it
Ice maker not making ice
Fixed by these parts
How to fix it
Won’t start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from BOCA RATON, FL
- Parts Used:
- W11820444, WPW10141622
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Original bracket foot brake screw hole was stripped and foot brake would not extend
The repair seemed simple, I just needed to remove the old bracket -- 4 screws -- and slip the new one on.
The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes, ... Read more I needed to shim up the side of the fridge that I was working on.
To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet.
The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes, ... Read more I needed to shim up the side of the fridge that I was working on.
To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from JAMESTOWN, NY
- Parts Used:
- WPW10383615
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The freezer wasn't defrosting.
took the old thermistor out and put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!