RV1299REW01 Roper Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Austin, TX
- Parts Used:
- 4387913
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Fridge Air On, Not Cooling
Previous issue with this refrigerator and I figure after the Hot summer we've had in TX that it overworked itself this summer in the garage! Caught this one before all was lost as it started it's not cooling cycle on a Sunday. Ordered the identical Relay&Overload from Parts Select, 2 days later I'm back to chilling the beer again! Super service with diagrams and specs. Very glad parts select is around!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from montgomery, NY
- Parts Used:
- W11117769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
No leveling legs
Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve
Steve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Frankfort, KY
- Parts Used:
- W11117769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Renters removed leveling legs from refrigerator. I don't know why!
I tilted the unit back enough to scew the new legs into the threaded holes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy L from Layton, UT
- Parts Used:
- 4-80576-202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken left arm to hold rack in
Just put the two screw back in that i had removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Radcliff, KY
- Parts Used:
- 4387913
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refrigerator would not get cold
Took a little while to figure out that I needed a flat tip screwdriver to lift up on the top of the plastic housing in order to tip it forward and remove it. After that I used pliers to remove the wires from the old parts and place them on the new. Removing and replacing the parts was performed by hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jabez from Holland, MI
- Parts Used:
- 4387913
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set
Freezer & Fridge warmed then stopped working
I oringinally thought it was one of the thermostats b/c the freezer started to freeze again after unplugging it. But then the next day it stopped all together and I could hear a clicking noise in the back and the compressor never turned on. It would click at around 2 minutes then again about 17 seconds later. I took photos of the original wires in the connector to match up later. The new parts were not identical to the old. The red wire on the bottom fit fine but the other two wires would not go in the same terminal or numbered positions (1&4). For 2 reasons, 1, the blue female was too small for the male and 2) there was a male missing at position 4. After looking at the guts of the old connector I decided to get new females (2 trips b/c I didn't buy a big enough wire opening - needed 2 wires) and cut, splice & crimp them. I then put the two females on the top two males & plugged it in. No sparks or explosions... but silence. I waited a few minutes and then the fan kicked on and then the compressor started running. That was Sunday, it's now Thursday and things are working well.
Was this instruction helpful to you?
Thank you for voting!