MZF34X20DW08 Maytag Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from BOCA RATON, FL
- Parts Used:
- WPW10515763, WPW10141622
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Original bracket foot brake screw hole was stripped and foot brake would not extend
The repair seemed simple, I just needed to remove the old bracket -- 4 screws -- and slip the new one on.
The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes, I needed to shim up the side of the fridge that I was working on.
To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet.
The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes, I needed to shim up the side of the fridge that I was working on.
To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from East Schodack, NY
- Parts Used:
- 4388239
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Broken rear cabinet rollers
Removed the rear cardboard cover and cleaned the area around the compressor and as much of the condensor and fan area as possible. Removed the two base section securing bolts. Jacked the rear of the cabinet up enough to seperate the base from the cabinet. Removed the roller pins and removed and replaced both rollers. Lowered the cabinet back into place, replaced the base bolts and the cardboard cover. The rollers that were sent were of much better quality than the original plastic type and should last the life of the refrigerator. Be careful when moving the fridge as the original rollers may cut into or scratch the flooring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from SOUTH ST PAUL, MN
- Parts Used:
- WPW10534161
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Clips on old toe kick plate were broken on one side. Would not stay on
Took the new kick plate out of the box. Snapped it into position. I have had a repairman for this refrigerator before. I would rather repair an appliance than buy a new one. I'm very proud that I thought to get a replacement part myself instead of calling my friendly repairman again. Saved a few dollars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victoria F, from NEWARK, NJ
- Parts Used:
- WPW10534161
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
None
Just put it into the bottom of the fridge and it snapped into place. NO PROBLEM AT ALL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sylvia from GREENVILLE, PA
- Parts Used:
- WPW10534161
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Part broke and was old
Bought a new psrt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from CASCADE, IA
- Parts Used:
- WPW10534161
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old one broke
snap the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothea from TOMS RIVER, NJ
- Parts Used:
- WPW10534161
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Easy to clip in place
No tools required, but you must be careful not to shove or jam this kick plate into place as it is a plastic part and not really very sturdy. This is the second time I have replaced the kick plate and PartSelect has always been knowledgeable, polite, and helpful
!!
!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Meredith from West Palm Beach, FL
- Parts Used:
- WPW10534161
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
bottom grille cover clip broke
To clip it in was easy. The hard part was getting down to do it. I'm 78, hubby is 80 and because of the fridge width it took both of us since we have a bottom freezer drawer. We don't get down or even up very well anymore. The part fit fine and looks great. The part arrived in less than 24 hours which pleasantly surprised us. Thanks much.!
Was this instruction helpful to you?
Thank you for voting!