25311301101 Kenmore Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Catrina from Calumet City, IL
- Parts Used:
- 297313200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door wasn't closing correctly.
My husband removed the old hinge, by taking out the old screws and the old hinge and attached the new one, by inserting the new hinge and the new screws. It was as easy as 123.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from AMERICAN CYN, CA
- Parts Used:
- 216480801
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
The freezer door gasket needed to be replaced.
When I received the new gasket I took a blow dryer to it and straightened out the warped areas prior to removing the old gasket. I then looked for a tool to remove the pins holding the gasket in place. I found a butter knife worked the best to get underneath and pry them out. Since this is a chest freezer, the pins in the back of the door were very hard to remove and one of them even broke off as I was removing it. Of course I had no spare pins when I went to put the new gasket in place. The new gasket slid right on and the pins snapped into place with a little bit of HARD pressure. My advice is to make sure that you do the back of the door first, since it is hard to line up the holes and the pins otherwise. It would not have been a difficult repair if not for the pins giving me trouble. There are no instructions sent showing how to do any of this work, so if you are not knowledgeable about gaskets this repair could be a difficult one. Maybe the company could include some basic instructions as a help to their customers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Butler, PA
- Parts Used:
- 297313200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Hinge Broken
Took out the screws(8mm). Used pliers to close new hinges. Re-installed the screws with as large washers as would fit(to hopefully prevent the hinges from cracking at the screw holes like the originals did). I like this supplier, part was easy to find, correct part, shipped fast, price was good.
Was this instruction helpful to you?
Thank you for voting!
Needed replacement because seal old and inner liner cracking
Very easy and simply. Take old stuff off, let insulation dry out and put all back together with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirleen from Olivet, MI
- Parts Used:
- 297313200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The freezer hinge was broke.
Took the broken one off & replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from OSTRANDER, OH
- Parts Used:
- 297313200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Hinge broke
I used a socket set and removed old one and replaced with new one. Easy as 1 2 3. And I'm s 55 yr old female.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ivan from MERLIN, OR
- Parts Used:
- 5304496559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
freezer would not start nor cool freeze
remove 2 screws from thermostat cover on side of freezer pulled temp nob off then removed temp control and copper temp sense rod by pulling out then unhook wires then reverse procedure to put back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from BON AQUA, TN
- Parts Used:
- 297313200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Broken hinge
Removed the bolts and broken hinge with lid closed. Installed new hinge. Removed the retaining nail from new hinge allowing it to have tension.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from COLORADO SPGS, CO
- Parts Used:
- 297313200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Broke freezer lid hinge.
Simple fix, the new hinge fit like a glove simple R&R.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Willowbrook, IL
- Parts Used:
- 216649304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer goes dead as a door nail
Having an electrical backround and with a multimeter, I quickly found the the bad component. Taking some satisfaction that the major components were all in good working order, I then began to think that the hardest part of this repair would be the hunt to find what I thought was an obscure part. This is where the internet shines. I found the part with the help of PartSelect and had the freezer back on track 3 days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reynold from Belen, NM
- Parts Used:
- 5304496559
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Thermostat would not hold the temperature
I replaced the thermostat. (Note: On a chest freezer, there is a copper tube going up into the wall of the freezer. The capillary of the thermostat goes into this tube.) 1. Unplug freezer. 2. Remove temperature knob. 3. Remove screws and remove cover plate. 4. Unclip old thermostat. 5. Using pliers, gently pull down the rubber seal on the capillary where it enters the copper tube. 6. Pull capillary out of copper tube. (In my case, the capillary was not free to pull out. I had to grasp the capillary with pliers and tug hard.) 7. Place rubber seal over the new capillary. 8. Insert the new capillary into the copper tube and put the rubber seal over the end of the copper tube. 9. Install thermostat body in the cover plate using the clip on the thermostat body. 10. Replace cover plate and temperature knob.
Was this instruction helpful to you?
Thank you for voting!