Models
>
25329111991
25329111991 Kenmore Freezer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$137.50
The gasket for your freezer door is used to provide a tight seal, preventing the cold air from escaping and warm room-temperature air from getting inside the freezer. If the gasket becomes torn, crack...
In Stock
Order now and your part arrives by Aug 13
$63.75
Ensure proper lighting inside your refrigerator with this 3.8W LED bulb, designed for use in various models. It provides clear, energy-efficient illumination to help you easily see stored items. If yo...
In Stock
Order now and your part arrives by Aug 13
In Stock
Order now and your part arrives by Aug 13
This is an adjustable foot for your freezer, refrigerator, and dryer. This part supports your unit by screwing into one of the bottom four corners, and adjusting the height of your machine. If your ap...
Special Order
In Stock
Order now and your part arrives by Aug 13
$30.60
This is a switch for your refrigerator, but you may also know it as a door switch or a plunger light switch. This part turns your appliance light on and off as the door is opened and closed. If your c...
In Stock
Order now and your part arrives by Aug 13
$20.01
This multi-use screw fits various appliances and tools such as, freezers, refrigerators, wall ovens, washers, ranges, dishwashers, dryers, microwave oven combos, combos, wine and beverage coolers. *Pl...
In Stock
Order now and your part arrives by Aug 13
On Order
This evaporator shelf trim is designed to snap onto the front edge of freezer or refrigerator shelves, providing a clean, finished look while helping keep items securely in place. The raised lip helps...
In Stock
Order now and your part arrives by Aug 13
In Stock
Order now and your part arrives by Aug 13
$60.36
This secondary door gasket is a replacement sealing component designed to help maintain proper internal temperatures and prevent air leakage. It supports efficient operation and is commonly replaced w...
In Stock
Order now and your part arrives by Aug 13
Common Problems and Symptoms for 25329111991
Viewing 4 of 4Frost buildup
Fixed by these parts
How to fix it
Too warm
Fixed by these parts
How to fix it
Doesn’t stop running
Fixed by these parts
How to fix it
Fridge too warm
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from RIXEYVILLE, VA
- Parts Used:
- 5304507199
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Gasket old and leaking
This freezer has many screws that hold the cover on the back of the door and assist clamping the edge of the gasket in place. Be sure to just loosen the screws 3/4 the way out, use a flat head screw driver to pry the cover from the door in case over time it is stuck to the door. The new gasket will come in a creative box trying not to kin
... Read more
k the gasket itself, but there will be some distortion of the gasket when you get it. Put it in the sun or in hot water. I put it in my dryer for 10 minutes. Remove the old gasket, and start at the top of the door to replace the gasket. TIPS: If the screws are backed out enough, there should not be any problem sliding the back part of the gasket under the cover. When on the sides, do not pull the gasket down to make it easier to slide the gasket underneath the cover. This will distort and lengthen the gasket so it will not fit and thin it out so it will not function well. Once the gasket is in place, tighten the screws being sure to feel along the outside edge of the gasket for any bulging that would indicate that portion of the gasket is NOT under the cover properly.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SEVIERVILLE, TN
- Parts Used:
- 5304507199
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Frost inside freezer.. Old door gasket leaking.
Pretty straight forward. Loosen all screws "but do not remove" pry door panel from door just enough to slip gasket behind panel. Make sure gasket is seated properly around door.. Tighten all screws snug...
Gasket may not seal right away due to being kinked from packaging, use a little heat on gasket witth hairdryer and push so ... Read more mething heavy against door over night. The gasket will straighten out over night.
Gasket may not seal right away due to being kinked from packaging, use a little heat on gasket witth hairdryer and push so ... Read more mething heavy against door over night. The gasket will straighten out over night.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from CARY, NC
- Parts Used:
- 5304507199
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer is 17 yrs old so needed a new gasket. The results were poor since the new gasket would not allow the door to seal.
Removed the numerous screws and took the door panel off. Cleaned and dried it. Replaced the insulation and hung the penal with 2 screws at the top and sides. Started to fit the gasket under the edge of the panel and put on the screws as I went across the top then down the sides finishing across the bottom. Perfect fit but could not get th
... Read more
e door to seal at all. Went out and bought a new freezer(did I say it was 17 yrs old?!?!).
Read less
Was this instruction helpful to you?
Thank you for voting!