Models
>
FH20M4WXFE
FH20M4WXFE Gibson Freezer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for FH20M4WXFE
Viewing 1 of 1
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Apr 6
$25.10
This is a screw and it is used with a variety of home appliances. It is less than 1/2 an inch long, and is #8-18 x 3/8. This part is a pan head, sheet metal, screw. It is made of metal.
In Stock
Order now and your part arrives by Apr 6
$19.63
This multi-use screw fits various appliances and tools such as, freezers, refrigerators, wall ovens, washers, ranges, dishwashers, dryers, microwave oven combos, combos, wine and beverage coolers. *Pl...
In Stock
Order now and your part arrives by Apr 6
$75.36
This freezer door hinge assembly supports the door and allows it to open and close smoothly while helping maintain a proper seal. It provides the stability needed to keep cold air inside and food stor...
In Stock
Order now and your part arrives by Apr 6
In Stock
Order now and your part arrives by Apr 6
In Stock
Order now and your part arrives by Apr 6
This part provides protection for the compressor motor against excessive current and excessive temperature use.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for FH20M4WXFE
Viewing 5 of 5Frost buildup
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Fridge too warm
Fixed by these parts
How to fix it
Freezer section too warm
Fixed by these parts
How to fix it
Won’t start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Melvin from Semmes, AL
- Parts Used:
- 216008900
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Clicking sound then within a minute clicking again, not cooling.
UNPLUG REFRIGERATOR. Carefully remove relay from the side of the compressor. You shouldn't need a tool to do this, if it is hard you can gently pry the edge with a flat head screw driver just to loosen. Unplug white and red wires from relay, noting that the white wire goes in the hole with a #2 stamped beside it. Shake old relay, if it r
... Read more
attles like a baby rattler then it's most likely the problem. Replace wires into the new relay and plug back into the compressor.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Jonestown, TX
- Parts Used:
- 216008900
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stopped working, cooling.
I used a small screwdriver to disconnect wires from old starter. I connected the overload and starter, two wires. I put the unit back in the keeper, plugged the unit in, turned up the thermostat and it's working beautifully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Neosho, MO
- Parts Used:
- 216008900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Freezer quit. Compressor would not start.
Like another post, the start relay rattled like a baby rattle. Replaced the start relay and freezer works great.
Was this instruction helpful to you?
Thank you for voting!