Models > FV21M2WXFE

FV21M2WXFE Gibson Freezer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for FV21M2WXFE

Viewing 3 of 3
CABINET PARTS Diagram and Parts List for Gibson Freezer
CABINET PARTS
DOOR PARTS Diagram and Parts List for Gibson Freezer
DOOR PARTS
SYSTEM AND ELECTRICAL PARTS Diagram and Parts List for Gibson Freezer
SYSTEM AND ELECTRICAL PARTS
Keep searches simple, eg. "belt" or "pump".
Door Shelf End Cap Set - Left and Right Side – Part Number: 5303925377
$49.29
This kit includes both the left and right side end caps.
In Stock
Order now and your part arrives by May 16
Gasket Retainer Clip Kit - 24 Pieces – Part Number: 5303922007
$62.61
These are used to hold your gasket in place.
In Stock
Order now and your part arrives by May 16
Shelf Support - Right Side – Part Number: 297001500
$27.83
In Stock
Order now and your part arrives by May 16
SCREW – Part Number: 216858001
$19.63
This multi-use screw fits various appliances and tools such as, freezers, refrigerators, wall ovens, washers, ranges, dishwashers, dryers, microwave oven combos, combos, wine and beverage coolers. *Pl...
In Stock
Order now and your part arrives by May 16
Shelf Support - Left Side – Part Number: 297001600
$27.83
Sold individually.
In Stock
Order now and your part arrives by May 16
Door Gasket – Part Number: 3206261
This gasket is intended for use with upright freezers. This white door gasket is used to make an air-tight seal for the cabinet when the door is closed
No Longer Available
Compressor Start Relay – Part Number: 216008900
No Longer Available
Interior Drain Plug – Part Number: 216502600
No Longer Available
Hinge Bearing – Part Number: 297006800
$21.82
In Stock
Order now and your part arrives by May 16
Filter - Drier – Part Number: 5303305677
$39.63
Refrigerant system filter/dryer.
In Stock
Order now and your part arrives by May 16
SUPPORT-REAR SHELF – Part Number: 216474600
No Longer Available
Compressor Mounting Grommet – Part Number: 216498900
$22.91
In Stock
Order now and your part arrives by May 16
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for FV21M2WXFE

Viewing 5 of 5
Frost buildup
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing
How to fix it
Fridge too warm
Fixed by these parts
Fixing
How to fix it
Freezer section too warm
Fixed by these parts
Fixing
How to fix it
Won’t start
Fixed by these parts
Fixing
How to fix it
Replacing the Compressor Start Relay

Replacing the Compressor Start Relay

View More
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Melvin from Semmes, AL
Parts Used:
216008900
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Clicking sound then within a minute clicking again, not cooling.
UNPLUG REFRIGERATOR. Carefully remove relay from the side of the compressor. You shouldn't need a tool to do this, if it is hard you can gently pry the edge with a flat head screw driver just to loosen. Unplug white and red wires from relay, noting that the white wire goes in the hole with a #2 stamped beside it. Shake old relay, if it r attles like a baby rattler then it's most likely the problem. Replace wires into the new relay and plug back into the compressor.
Read less
81 of 97 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sharon from Green Valley Lake, CA
Parts Used:
3206261
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The freezer was going into alarm
We loosened all the screws around the door and slid out the old gasket.
We then slid the new gasket behind the panel and screwed the screws back in place.
36 of 43 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jennifer from Jonestown, TX
Parts Used:
216008900
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Stopped working, cooling.
I used a small screwdriver to disconnect wires from old starter. I connected the overload and starter, two wires. I put the unit back in the keeper, plugged the unit in, turned up the thermostat and it's working beautifully.
15 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More