FUF17DAARWH General Electric Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paulette from Great Falls, MT
- Parts Used:
- WR02X12310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The freezer door was catching when opened and frost was building inside telling me that the seal wasn't good.
I called the local GE dealer for repair. The repair person arrived and told me that he could not get the part. The freezer was too old. Then he charged me $60 for coming out. I went online and did a search for parts with the model number above. I found Partselect.com and the diagrams showed which part I needed. It was in stock and I ordered it. My husband and I removed the door to the freezer, pushed the part into the hole at the bottom of the door and put the door back on its hinges. It works perfectly. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Elverta, CA
- Parts Used:
- WR09X10154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
freezer kept icing up on the coils would only get down to 20 degrees.
unplug the freezer. remove the 2 screws holding the timer, unplug the electrical fitting w/4 prongs. reverse the steps and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Marion, KY
- Parts Used:
- WR07X10015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Tempture Got Hot In Box. The Compressor Was Making A Clicking Sound.
First I tested the compressor with my v. O. Meter and it was ok I then found the relay was bad I removed the start relay by puling it off the compressor & removed the run wire & start wire watching not to cross them & reversed to re install. Now it runs good again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hazel from FRIENDSWOOD, TX
- Parts Used:
- WR14X28402
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Gasket not sealing
Per the UTube video ...
Once the gasket was on, the door would not seal.
Gasket was removed and placed in dryer again to "soften" but to no avail on the second try.
When we received the package, the box was ripped open and only the wadded up gasket in the box. Don't know if someone just shoved it in or what. I think this is what caused the issue with it not sealing. Also no instructions except on your website. We ended up putting on the original gasket and sealed the cut on the gasket with tape. Freezer seals well and no leaks or issues. I still have the gas but no clue what to do with it if we can't get it to work. Is there a refund available?
Once the gasket was on, the door would not seal.
Gasket was removed and placed in dryer again to "soften" but to no avail on the second try.
When we received the package, the box was ripped open and only the wadded up gasket in the box. Don't know if someone just shoved it in or what. I think this is what caused the issue with it not sealing. Also no instructions except on your website. We ended up putting on the original gasket and sealed the cut on the gasket with tape. Freezer seals well and no leaks or issues. I still have the gas but no clue what to do with it if we can't get it to work. Is there a refund available?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from las cruces, NM
- Parts Used:
- WR01X26468
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The freezer was missing the key
I ordered a pair of new keys from Parts Select and found the website extremely easy to use. I found the key I needed in less than 10 minutes and ordered the item. The key woked perfectly. Delivery was prompt and the cost was resonable. I have bookmarked the site for future use. thank you. James
Was this instruction helpful to you?
Thank you for voting!