Models
>
FP21DSDRWH
FP21DSDRWH General Electric Freezer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for FP21DSDRWH
Viewing 3 of 3Keep searches simple, eg. "belt" or "pump".
In Stock
This door shelf retainer bar end cap kit contains two white end caps.
No Longer Available
In Stock
This white door gasket is used to seal the door when closed to keep the cool air inside and the room air out.
No Longer Available
Special Order
$62.27
The filter dryer filters refrigerant that travels through the sealed system of the refrigerator.
In Stock
Special Order
In Stock
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for FP21DSDRWH
Viewing 2 of 2Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paulette from Great Falls, MT
- Parts Used:
- WR02X12310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The freezer door was catching when opened and frost was building inside telling me that the seal wasn't good.
I called the local GE dealer for repair. The repair person arrived and told me that he could not get the part. The freezer was too old. Then he charged me $60 for coming out. I went online and did a search for parts with the model number above. I found Partselect.com and the diagrams showed which part I needed. It was in stock and I
... Read more
ordered it. My husband and I removed the door to the freezer, pushed the part into the hole at the bottom of the door and put the door back on its hinges. It works perfectly. Thank you.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce K from RESTON, VA
- Parts Used:
- WR2X5676
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Two of the two leveling jacks of this old refrigerator were missing and had to be replaced.
I ordered four leveling jacks from this site for the refrigerator using a slightly different model number (my model was not listed). I assumed that the jacks all had the same shaft diameter and thread size. However, it turned out that the two front jacks had half-inch shaft diameters. It could be that originally there were rollers in fro
... Read more
nt. The two rear jacks had quarter-inch shafts with "feet" for supporting them on the floor. So, I had to return the four jacks I had ordered and find another solution. I found two half-inch threaded bolts at the local hardware store that fit the front holes perfectly. I purchased 3.5 inch bolts to give me enough room to find the proper adjustment. I used wooden blocks and a crow bar to raise one side of the refrigerator high enough to screw in the leveling jacks. I used an adjustable crescent wrench to turn the bolts' hex heads until they were the proper height. I used the two original quarter-inch jacks in the rear holes and adjusted them to the proper height to level the refrigerator on the concrete floor where it is located. Then I removed the wooden blocks and tested to make sure the refrigerator did not wobble. I found that using the two bolts (no leveling jacks for the front holes could be found) for the front jacks proved to be the ideal solution. The job took me about thirty minutes, including the time it took to move the refrigerator into its final location and adjust the leveling jacks once more to create a solid stance so that the refrigerator did not wobble. While I had the refrigerator away from the wall, I removed the rear panel and cleaned the blades of the cooler fan and removed dust and dirt build up near the compressor with a vacuum cleaner. Then, I screwed the panel back into position, moved the refrigerator into its final place in a corner of the garage and made sure there was enough air space around it to allow for proper air circulation. This took me about twenty more minutes. I plugged it back in and listened to it come alive again. It is old but has never needed a repair and keeps everything cooled or frozen. I would suggest using threaded hex-head bolts in place of original leveling jacks if they cannot be obtained. Problem solved.
Read less
Was this instruction helpful to you?
Thank you for voting!