49651-0C Frigidaire Freezer - Instructions

UNPLUG REFRIGERATOR. Carefully remove relay from the side of the compressor. You shouldn't need a tool to do this, if it is hard you can gently pry the edge with a flat head screw driver just to loosen. Unplug white and red wires from relay, noting that the white wire goes in the hole with a #2 stamped beside it. Shake old relay, if it rattles like a baby rattler then it's most likely the problem. Replace wires into the new relay and plug back into the compressor.

We loosened all the screws around the door and slid out the old gasket.
We then slid the new gasket behind the panel and screwed the screws back in place.

It was very easy to remove the broken parts of the freezer door handle still secured by screws and then attach the new handle. However, I was shocked to find that the door handle screw cover plate was not included as part of the door handle replacement issued, which I felt was misleading. Fortunately that portion from my old broken handle was still intact, though is yellowed with age, so was able to snap that in place on the new partial-handle replacement which you sent. It seems to me that to omit this portion as part of the complete handle replacement didn't make much sense, as it rendered the new replacement handle incomplete.

I used a small screwdriver to disconnect wires from old starter. I connected the overload and starter, two wires. I put the unit back in the keeper, plugged the unit in, turned up the thermostat and it's working beautifully.

Like another post, the start relay rattled like a baby rattle. Replaced the start relay and freezer works great.

i looked byhind the freezer , the mottor has the relay connected to it.i took out the relay, and i descovery something was loose inside, i decided to take to check out at sears to see if they have in stock that especific relay. they did not have, they could order, that's when i dicided to go ahead and looking for in the internet, good i found PARTSELECT,they had the part and i was very nice attended,they sent in 2 days i had fix my freezer. thanks PARTSELECT. gilmar couto.

Inserted end pieces and remounted old refrigerator bar

hardest part was to remove deformities using a hair dryer. Working with hand after heating seemed to work but was not quick.
Loosen screws under old gasket. Screws hold gasket lip under the edge of the door liner. Remove old gasket. As door liner was brittle from age, I used silicone caulk across top of door behind flange, set lip of gasket in silicone and tighten screws. Did top and half was down the side, then did the bottom up, taking ank excess gasket and trying to distribute along straight side. Make sure door is plum and square on hinges, then close door. Turned freezer on and allow to cool to see if ice would form, before refilling with food.

The easiest way to replace this gasket is to remove the door from the freezer. Two bolts remove the top hinge and the door pops off. Setting it on sawhorses makes the job easy. In addition, I moved the door into the sunlight which made the gasket flexible and easy to work with.

Remove the screws under the gasket with a phillips screwdriver and lift the inner panel off the door. Clean the area when the gasket sits, put the new gasket in place and replace the inner panel and all the screws.

Opened mailer and bag and place the drain plug into the drain. fit perfectly. In fact it is better than the one lost since the original needed a screwdriver or tool to remove the plug. This one has a flang or finger turner on it so that it can be removed. Also, does not interfere with items in bottom of freezer.

slid one end cap into slot and pulled into place. Put other end cap into cross bar and put other end of cross bar on to other end cap proceeded to put other end cap in to other slot in door and pulled into place. Job complete Job took less than three minutes.

Old handle was off already. Took the to screws from old handle, put the new one on screwed it on and that did it.

I ordered the handle , which was easy and resonable priced.
I used a cordless screw driver . And it was done in under 30 seconds . Quick repair

By simply popping off the handle cover the two screws were revealed which attach the handle to the door. New handle fit exactly like the old one. Easy peezzy lemon squeezy.

Finally after a few years of putting the shelf back on and balancing food on it I looked up the part.
The clips came in a few days.
I used a screwdriver to pop off the old piece. I lined up the clip and pushed it in.!
I am sooo glad I purchased this.