49152-0B Frigidaire Freezer - Instructions

UNPLUG REFRIGERATOR. Carefully remove relay from the side of the compressor. You shouldn't need a tool to do this, if it is hard you can gently pry the edge with a flat head screw driver just to loosen. Unplug white and red wires from relay, noting that the white wire goes in the hole with a #2 stamped beside it. Shake old relay, if it rattles like a baby rattler then it's most likely the problem. Replace wires into the new relay and plug back into the compressor.

It was very easy to remove the broken parts of the freezer door handle still secured by screws and then attach the new handle. However, I was shocked to find that the door handle screw cover plate was not included as part of the door handle replacement issued, which I felt was misleading. Fortunately that portion from my old broken handle was still intact, though is yellowed with age, so was able to snap that in place on the new partial-handle replacement which you sent. It seems to me that to omit this portion as part of the complete handle replacement didn't make much sense, as it rendered the new replacement handle incomplete.

I used a small screwdriver to disconnect wires from old starter. I connected the overload and starter, two wires. I put the unit back in the keeper, plugged the unit in, turned up the thermostat and it's working beautifully.

Like another post, the start relay rattled like a baby rattle. Replaced the start relay and freezer works great.

Simple switch repair: Unplug fridge, pull down to remove switch assembly, slip contacts off. Reverse with replacement switch. HOWEVER, check first to see if the bulb filament might be broken, as this could cause the same symptom. OR in my case, the light socket connection was the culprit. Check that too before ordering a replacement switch.

i looked byhind the freezer , the mottor has the relay connected to it.i took out the relay, and i descovery something was loose inside, i decided to take to check out at sears to see if they have in stock that especific relay. they did not have, they could order, that's when i dicided to go ahead and looking for in the internet, good i found PARTSELECT,they had the part and i was very nice attended,they sent in 2 days i had fix my freezer. thanks PARTSELECT. gilmar couto.

The repair was really easy - I used a phillips head screw driver to remove the screws and broken pieces of the handle, screwed the new one on and snapped the handle insert into place. I was thrilled to be able to find the parts so easily (the information you have online is really helpful!), the parts arrived much faster than I anticipated and the handle was easily replaced! Thank you!

Opened mailer and bag and place the drain plug into the drain. fit perfectly. In fact it is better than the one lost since the original needed a screwdriver or tool to remove the plug. This one has a flang or finger turner on it so that it can be removed. Also, does not interfere with items in bottom of freezer.

slid one end cap into slot and pulled into place. Put other end cap into cross bar and put other end of cross bar on to other end cap proceeded to put other end cap in to other slot in door and pulled into place. Job complete Job took less than three minutes.

Old handle was off already. Took the to screws from old handle, put the new one on screwed it on and that did it.

installed new handle

I ordered the handle , which was easy and resonable priced.
I used a cordless screw driver . And it was done in under 30 seconds . Quick repair

Removed the freezer door which had an electrical cord routed through the lower hinge with a disconnect under the freezer. Job works better with two people. Working the gasket into place was a little tricky at the corners. The putty knife was helpful. Make sure door is not warped when replaced on freezer. If warped slightly the door can be twisted to make gasket fit evenly bottom to top on front edge. Hope this helps DIY folks.

Ordered the replacement handle and insert. I replaced the handle in about 10 minutes.

By simply popping off the handle cover the two screws were revealed which attach the handle to the door. New handle fit exactly like the old one. Easy peezzy lemon squeezy.