MFU20F3BW2 Frigidaire Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kelly from Gladstone, OR
- Parts Used:
- 5304442620
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer too warm
Removed two screws and wire harness from old motor. Put in new motor and connected wire harness.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GEORGE from WEST LIBERTY, OH
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end cap broke
slid one end cap into slot and pulled into place. Put other end cap into cross bar and put other end of cross bar on to other end cap proceeded to put other end cap in to other slot in door and pulled into place. Job complete Job took less than three minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Provo, UT
- Parts Used:
- 5303925377
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
No instructions included
Visual assessment and put in by hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from SELDEN, NY
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The end cap of the bottom shelf of my freezer was broken
Finally after a few years of putting the shelf back on and balancing food on it I looked up the part.
The clips came in a few days.
I used a screwdriver to pop off the old piece. I lined up the clip and pushed it in.!
I am sooo glad I purchased this.
The clips came in a few days.
I used a screwdriver to pop off the old piece. I lined up the clip and pushed it in.!
I am sooo glad I purchased this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D from Fairport, NY
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken pieces
replaced them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Enfield, NH
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken shelf end
snapped in the new shelf end and we were back in business. Thanks for the great & fast service RJL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RUDOLPH from PRINCETON, TX
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken door shelf end brackets
Push-in replacement - easy. I must note that I received my order within two days - remarkable service from Part Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from Merrill, MI
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken door end cap.
I was so supprised that Part slect was around and had the part . You can count on me to tell others about your wonderful service . I will see to it that I use your service when somthing else goes wrong with any of my appliences
Thanks again !
Thanks again !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Spring Green, WI
- Parts Used:
- 5303925377
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
door shelf useless
Decide how to snap end cap into door.
Put one end on door.
Fasten bar, then with other end cap
in the bar, snap it into the door.
Put one end on door.
Fasten bar, then with other end cap
in the bar, snap it into the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Woodstock, GA
- Parts Used:
- 5304442620
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Fan in freezer quit
This was an easy job. First remove the ice maker, if you have one. Mine was mounted with just two screws. Loosen these screws, unplug the power cord at the connector and then lift the ice maker off. Remove the light bulb cover and the light bulb, just so you dont break it. Remove two hex screws and the back cover can be removed. My fan was mounted in the middle of a bracket retained between two rubber bushingings. Just push the fan blad of the shaft and pull the motoer out. Dissonect the power cord at the connector. My moter was differant than the replacement on the mounting so with the removial of the two screws on the motor I was able to exchange the upper and lower cast motoer housings. Reverse the assembly process and you good. Mine is running great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donn from Saint PAUL, MN
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf end cap
Truly a 10-second fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Littleton, CO
- Parts Used:
- 5303925377
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The tabs on the shelf end broke off.
Removed the broken shelf ends and installed the new ones. Then installed the assembly on the freezer door. Trick was to put the long end of the tab in first followed by the short end. The up end was reversed on the opposite shelf end.
Was this instruction helpful to you?
Thank you for voting!