UL2075ECW3 Frigidaire Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Melvin from Manning, IA
- Parts Used:
- 5303925378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The end caps of the door shelf bracket broke
Put the end caps on the ends of the shelf bracket and returned the bracket to the proper place in the freezer.
Just wanted to add that the service and helpfulness to get this part for a freezer that is close to 30 years old was super. After almost 30 years, this was the first thing to go wrong with this freezer. We did not expect to be able to find this little part for repair but thanks to fantastic help, our freezer is in good shape again. Thank you !
Just wanted to add that the service and helpfulness to get this part for a freezer that is close to 30 years old was super. After almost 30 years, this was the first thing to go wrong with this freezer. We did not expect to be able to find this little part for repair but thanks to fantastic help, our freezer is in good shape again. Thank you !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FREDDIE from WHITAKERS, NC
- Parts Used:
- 5303276514, 5303007173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Freezer stopped freezing food.
I unplugged electrical cord to the freezer. I removed the cover to the relay and load protector. I labeled the wires and made a diagram on the proper placement of each wire going to the relay. I unplugged each wire and removed the relay. Then I removed the load protector. I installed the new load protector and new relay. I placed the wires on the proper terminals of the relay. I replaced the electrical cover to the relay and load protector. I plugged the electrical cord back in the electrical outlet. My freezer started working again. I placed several bottles of water in the freezer to make sure the freezer was working properly before I restocked it with food.
Thanks again for the help. You just saved me about $400.
Thanks again for the help. You just saved me about $400.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D KIRKE from CORVALLIS, OR
- Parts Used:
- 5309918806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Erratic light.
Simple switch repair: Unplug fridge, pull down to remove switch assembly, slip contacts off. Reverse with replacement switch. HOWEVER, check first to see if the bulb filament might be broken, as this could cause the same symptom. OR in my case, the light socket connection was the culprit. Check that too before ordering a replacement switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from LISLE, IL
- Parts Used:
- 216502600
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
While defrosting freezer tossed the drain plug with ice and water into the sewer system.
Opened mailer and bag and place the drain plug into the drain. fit perfectly. In fact it is better than the one lost since the original needed a screwdriver or tool to remove the plug. This one has a flang or finger turner on it so that it can be removed. Also, does not interfere with items in bottom of freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James H from KNOXVILLE, TN
- Parts Used:
- 3206256
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Ice crystals formed near gasket.
Removed the freezer door which had an electrical cord routed through the lower hinge with a disconnect under the freezer. Job works better with two people. Working the gasket into place was a little tricky at the corners. The putty knife was helpful. Make sure door is not warped when replaced on freezer. If warped slightly the door can be twisted to make gasket fit evenly bottom to top on front edge. Hope this helps DIY folks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Keystone, NE
- Parts Used:
- 297181900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light burned out on the door lid
Used a thin screwdriver to lift out the burned out light assembly. Unplugged the old light unit and installed the new one. Plugged in the freezer and the light worked. Easy as pie.
Was this instruction helpful to you?
Thank you for voting!
Plastic shelf supports broken
Needed to remove both left and right broken (plastic) supports and reinsert the new parts. Not hard at all...worked like a charm!
Was this instruction helpful to you?
Thank you for voting!