FFT49651-0A Frigidaire Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sharon from Green Valley Lake, CA
- Parts Used:
- 3206261
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The freezer was going into alarm
We loosened all the screws around the door and slid out the old gasket.
We then slid the new gasket behind the panel and screwed the screws back in place.
We then slid the new gasket behind the panel and screwed the screws back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FREDDIE from WHITAKERS, NC
- Parts Used:
- 5303276514, 5303007173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Freezer stopped freezing food.
I unplugged electrical cord to the freezer. I removed the cover to the relay and load protector. I labeled the wires and made a diagram on the proper placement of each wire going to the relay. I unplugged each wire and removed the relay. Then I removed the load protector. I installed the new load protector and new relay. I placed the wires on the proper terminals of the relay. I replaced the electrical cover to the relay and load protector. I plugged the electrical cord back in the electrical outlet. My freezer started working again. I placed several bottles of water in the freezer to make sure the freezer was working properly before I restocked it with food.
Thanks again for the help. You just saved me about $400.
Thanks again for the help. You just saved me about $400.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from UNION, ME
- Parts Used:
- 3206261
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Replace upright freezer door gasket.
The easiest way to replace this gasket is to remove the door from the freezer. Two bolts remove the top hinge and the door pops off. Setting it on sawhorses makes the job easy. In addition, I moved the door into the sunlight which made the gasket flexible and easy to work with.
Remove the screws under the gasket with a phillips screwdriver and lift the inner panel off the door. Clean the area when the gasket sits, put the new gasket in place and replace the inner panel and all the screws.
Remove the screws under the gasket with a phillips screwdriver and lift the inner panel off the door. Clean the area when the gasket sits, put the new gasket in place and replace the inner panel and all the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald R from BAHAMA, NC
- Parts Used:
- 3206261
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Freezer developing ice inside
hardest part was to remove deformities using a hair dryer. Working with hand after heating seemed to work but was not quick.
Loosen screws under old gasket. Screws hold gasket lip under the edge of the door liner. Remove old gasket. As door liner was brittle from age, I used silicone caulk across top of door behind flange, set lip of gasket in silicone and tighten screws. Did top and half was down the side, then did the bottom up, taking ank excess gasket and trying to distribute along straight side. Make sure door is plum and square on hinges, then close door. Turned freezer on and allow to cool to see if ice would form, before refilling with food.
Loosen screws under old gasket. Screws hold gasket lip under the edge of the door liner. Remove old gasket. As door liner was brittle from age, I used silicone caulk across top of door behind flange, set lip of gasket in silicone and tighten screws. Did top and half was down the side, then did the bottom up, taking ank excess gasket and trying to distribute along straight side. Make sure door is plum and square on hinges, then close door. Turned freezer on and allow to cool to see if ice would form, before refilling with food.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GEORGE from WEST LIBERTY, OH
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end cap broke
slid one end cap into slot and pulled into place. Put other end cap into cross bar and put other end of cross bar on to other end cap proceeded to put other end cap in to other slot in door and pulled into place. Job complete Job took less than three minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from SELDEN, NY
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The end cap of the bottom shelf of my freezer was broken
Finally after a few years of putting the shelf back on and balancing food on it I looked up the part.
The clips came in a few days.
I used a screwdriver to pop off the old piece. I lined up the clip and pushed it in.!
I am sooo glad I purchased this.
The clips came in a few days.
I used a screwdriver to pop off the old piece. I lined up the clip and pushed it in.!
I am sooo glad I purchased this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Provo, UT
- Parts Used:
- 5303925377
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
No instructions included
Visual assessment and put in by hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D from Fairport, NY
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken pieces
replaced them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Enfield, NH
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken shelf end
snapped in the new shelf end and we were back in business. Thanks for the great & fast service RJL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RUDOLPH from PRINCETON, TX
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken door shelf end brackets
Push-in replacement - easy. I must note that I received my order within two days - remarkable service from Part Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from Merrill, MI
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken door end cap.
I was so supprised that Part slect was around and had the part . You can count on me to tell others about your wonderful service . I will see to it that I use your service when somthing else goes wrong with any of my appliences
Thanks again !
Thanks again !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Spring Green, WI
- Parts Used:
- 5303925377
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
door shelf useless
Decide how to snap end cap into door.
Put one end on door.
Fasten bar, then with other end cap
in the bar, snap it into the door.
Put one end on door.
Fasten bar, then with other end cap
in the bar, snap it into the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Littleton, CO
- Parts Used:
- 5303925377
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The tabs on the shelf end broke off.
Removed the broken shelf ends and installed the new ones. Then installed the assembly on the freezer door. Trick was to put the long end of the tab in first followed by the short end. The up end was reversed on the opposite shelf end.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donn from Saint PAUL, MN
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf end cap
Truly a 10-second fix.
Was this instruction helpful to you?
Thank you for voting!