Models
>
406777-0116-E1
406777-0116-E1 Briggs and Stratton Engine
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 406777-0116-E1
Viewing 8 of 8
Keep searches simple, eg. "belt" or "pump".
$8.27
This is a replacement push rod for your lawn tractor engine. It is made of aluminum and is the push rod used for the exhaust valve. Occasionally, the push rod in your engine can become damaged, and wi...
In Stock
$7.65
This part includes one manufacturer-approved rocker cover gasket for a lawn tractor. This gasket is for the cylinder head where it creates a tight seal to protect the equipment from leaks. Over time t...
In Stock
In Stock
$14.38
This is a manufacturer-approved oil filter replacement, sold independently. The oil filter is essential in preventing damaging impurities from mixing with the engine oil. Having a well-maintained oil ...
In Stock
In Stock
In Stock
In Stock
$37.66
This genuine crankcase gasket is used on small lawn and garden engines. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need...
In Stock
In Stock
$26.91
This is a replacement cylinder head gasket for your small engine. The gasket is approximately 5 inches in length and 5 inches in width at its longest and widest points. The gasket creates a seal, and ...
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 406777-0116-E1
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the head blew a vaulve guide destoying push rods
about 6 hours to tear down and replace don't do it in the hot sun needed more breaks takes longer, but the new factory heads did it started up 185 lbs of compression almost back to new, so much more power than old one's. FYI take off the motor cover every year clean out the debris (grass-mouse nest- and oil) it blocks the air and COOKS
... Read more
THE HEAD it only takes short time and will make that motor last a little longer but it is a BRIGGS engine
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D from HUNTSVILLE, AL
- Parts Used:
- 796232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Engine quit due to valve guide sliding out causing rocker arm to be immovable resulting in bent push rods.
Clean engine with a Gunk type product. Remove valve cover. Loosen bolts and remove old cylinder head. One bolt is located inside valve cover area. Remove old gasket and inspect and clean that surface. Attach new head with new gasket using existing bolts. Torque to 18'#s with a cross type pattern. Attach new rocker arms and push rods. Set
... Read more
valve clearance to .004 - .006. Attach valve cover with gasket. Check oil level. Start and let it warm up. Let cool remove cover then check valve clearance again. Replace cover.
Read less
Was this instruction helpful to you?
Thank you for voting!
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet t
... Read more
o remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions
Read less
Was this instruction helpful to you?
Thank you for voting!