Models
>
406777-0027-E1
406777-0027-E1 Briggs and Stratton Engine
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 406777-0027-E1
Viewing 8 of 8
Keep searches simple, eg. "belt" or "pump".
This is a replacement push rod for your lawn tractor engine. It is made of aluminum and is the push rod used for the exhaust valve. Occasionally, the push rod in your engine can become damaged, and wi...
No Longer Available
$9.20
This part includes one manufacturer-approved rocker cover gasket for a lawn tractor. This gasket is for the cylinder head where it creates a tight seal to protect the equipment from leaks. Over time t...
In Stock
Order now and your part arrives by Mar 20
In Stock
Order now and your part arrives by Mar 20
$7.90
This is a genuine OEM sourced replacement part designed for use with a variety of lawn and garden equipment. This item fits the cylinder and helps to provide an air tight seal to prevent any leaks. It...
In Stock
Order now and your part arrives by Mar 20
$29.39
This is a replacement cylinder head gasket for your small engine. The gasket is approximately 5 inches in length and 5 inches in width at its longest and widest points. The gasket creates a seal, and ...
In Stock
Order now and your part arrives by Mar 20
$16.85
This is a manufacturer-approved oil filter replacement, sold independently. The oil filter is essential in preventing damaging impurities from mixing with the engine oil. Having a well-maintained oil ...
In Stock
Order now and your part arrives by Mar 20
$51.95
This genuine crankcase gasket is used on small lawn and garden engines. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need...
In Stock
Order now and your part arrives by Mar 20
$6.25
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Plier...
In Stock
Order now and your part arrives by Mar 20
$6.25
This item is an authentic OEM part. It is used in various models of Toro tractors and Briggs & Stratton engines. An o-ring is used to seal and protect in between rigid connected pieces. Proper seal is...
In Stock
Order now and your part arrives by Mar 20
$39.75
This gear-governor is a special component that helps to engage the drive shaft. It is a genuine Briggs and Stratton item that is supplied by the original manufacturer for use with small engines that a...
On Order
In Stock
Order now and your part arrives by Mar 20
$6.25
This is a genuine OEM sourced replacement exhaust gasket. It is specially made for use with Briggs and Stratton engines commonly used on Toro lawn and garden equipment. Its purpose is to provide an ai...
In Stock
Order now and your part arrives by Mar 20
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 406777-0027-E1
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the head blew a vaulve guide destoying push rods
about 6 hours to tear down and replace don't do it in the hot sun needed more breaks takes longer, but the new factory heads did it started up 185 lbs of compression almost back to new, so much more power than old one's. FYI take off the motor cover every year clean out the debris (grass-mouse nest- and oil) it blocks the air and COOKS
... Read more
THE HEAD it only takes short time and will make that motor last a little longer but it is a BRIGGS engine
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D from HUNTSVILLE, AL
- Parts Used:
- 84001919
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Engine quit due to valve guide sliding out causing rocker arm to be immovable resulting in bent push rods.
Clean engine with a Gunk type product. Remove valve cover. Loosen bolts and remove old cylinder head. One bolt is located inside valve cover area. Remove old gasket and inspect and clean that surface. Attach new head with new gasket using existing bolts. Torque to 18'#s with a cross type pattern. Attach new rocker arms and push rods. Set
... Read more
valve clearance to .004 - .006. Attach valve cover with gasket. Check oil level. Start and let it warm up. Let cool remove cover then check valve clearance again. Replace cover.
Read less
Was this instruction helpful to you?
Thank you for voting!
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet t
... Read more
o remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions
Read less
Was this instruction helpful to you?
Thank you for voting!