Models
>
122H02-0220-B1
122H02-0220-B1 Briggs and Stratton Engine
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 122H02-0220-B1
Viewing 5 of 5
Keep searches simple, eg. "belt" or "pump".
$6.84
This replacement cap-fuel is a genuine OEM supplied item, not an aftermarket imitation. It is a high quality part commonly used on Murray and Toro snow throwers and lawn mowers. It is used to keep the...
In Stock
Order now and your part arrives by Apr 6
$9.13
This is a filter cartridge for the air filter in various lawn equipment. The filter removes dirt, dust, and other debris from entering the carburetor, and contaminating the engine. If the engine in yo...
In Stock
Order now and your part arrives by Apr 6
$6.51
This is a spark plug and it is found in various lawn equipment. If your engine is not starting or running poorly, you may need to replace the spark plug. This part is a RJ9LM. Meaning, it is a resisto...
In Stock
Order now and your part arrives by Apr 6
$24.70
This is a replacement carburetor overhaul kit for your small engine. The carburetor is essential to the overall performance of your engine, and the carb can get clogged up over time for a variety of r...
In Stock
Order now and your part arrives by Apr 6
$6.51
Genuine OEM replacement part, this item is sold individually. The 795629 Air Cleaner Gasket is attached to the part number 795259 Air Cleaner Base on one side and to the Carburetor on the other side. ...
In Stock
Order now and your part arrives by Apr 6
$6.51
This is an OEM primer bulb and clip. It is attached to the engine air filter base. When the primer bulb is pushed, this fills the carburetor with fuel, making it easier to start a cold engine. This ru...
In Stock
Order now and your part arrives by Apr 6
$6.51
This Genuine OEM ratchet pawl is a critical component designed to engage the recoil starting system with the engine, ensuring smooth and reliable starts. Manufactured from durable plastic, this replac...
In Stock
Order now and your part arrives by Apr 6
$9.06
Genuine manufacturer approved carburetor needle valve for lawn and garden equipment engines. This item includes the seat. The needle valve opens and closes to control the flow of fuel into the carbure...
In Stock
Order now and your part arrives by Apr 6
$52.07
This genuine OEM engine gasket set is sourced directly from the manufacturer and includes the gaskets needed to seal the components in a gas-powered engine. This set ensures proper fit and performance...
In Stock
Order now and your part arrives by Apr 6
$25.98
This manufacturer approved recoil starter pulley is designed for lawn and garden equipment engines. The recoil starter engages the drive cup on the flywheel to start the engine when pulled. This assem...
In Stock
Order now and your part arrives by Apr 6
$8.00
This part is the replacement gasket for the crankcase on your engine. The gasket helps to create a seal on the crankcase and prevent leaks. If you notice that your engine is not running at peak perfor...
In Stock
Order now and your part arrives by Apr 6
$6.51
This is a Genuine OEM Authorized Gasket used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recom...
In Stock
Order now and your part arrives by Apr 6
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 122H02-0220-B1
Viewing 3 of 3Will Not Start
Fixed by these parts
How to fix it
Engine will not idle
Fixed by these parts
How to fix it
Cannot pull starter cord out or engine will not turn over
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Mower was submerged in Hurricane Matthew
Total disassemble, clean out water and any rust. hone cylinder, wire brush where needed,reassemble with new rings,gaskets and seals and lucas oil product. Started on second pull. Mowed lawn. If you have never done this sort of work before, probably should not attempt.
Was this instruction helpful to you?
Thank you for voting!
Mower body was die cast and in good condition. Engine was burning oil.
Removed engine, no specialty tools required. Honed the cylinder, and lapped the valves. Tip on compressing valve spring for reassembly; compress springs with you finger and tie them with 2 zip ties, cut the zip ties after installing the keepers. Repainted the mower deck and engine. It runs and looks like new. My Toro is a 1999 model .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dustin from BANGOR, ME
- Parts Used:
- 590508
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set, Wrench set
Leaking gaskets
All the gaskets needed to be replaced on the Briggs 6.75 flathead I was rebuilding. I ported and polished the ports and shaved the eyebrow between the valves and the piston. The gasket set was a perfect fit. It is a monster now. It doesn't sound like a lawnmower engine anymore
Was this instruction helpful to you?
Thank you for voting!