Models
>
082232-0326-01
082232-0326-01 Briggs and Stratton Engine
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 082232-0326-01
Viewing 12 of 12
Keep searches simple, eg. "belt" or "pump".
$9.13
This is a filter cartridge for the air filter in various lawn equipment. The filter removes dirt, dust, and other debris from entering the carburetor, and contaminating the engine. If the engine in yo...
In Stock
Order now and your part arrives by Mar 27
$6.51
This is a spark plug and it is found in various lawn equipment. If your engine is not starting or running poorly, you may need to replace the spark plug. This part is a RJ9LM. Meaning, it is a resisto...
In Stock
Order now and your part arrives by Mar 27
$6.51
This is an OEM replacement part, sold individually. This Grommet is an elbow for the crankcase breather tube. These rubber elbows were just a convenient way to make a 90 degree bend back when they us...
In Stock
Order now and your part arrives by Mar 27
$47.95
This is the replacement carburetor kit for your small engine, used for outdoor power equipment. The carburetor rebuild kit includes the float, needle, gaskets, and seals that you need to refurbish you...
On Order
$6.51
Genuine OEM replacement Grommet used on Lawn and Garden equipment Engines. This Rubber breather grommet is used as a seal between Breather Assembly and the Breather Tube. Over time rubber grommet may ...
In Stock
Order now and your part arrives by Mar 27
$4.15
This is a Genuine Briggs & Stratton part used on 3-5 HP horizontal Pulsa-Jet Carburetor engines (new style). This part is sold individually. Diaphragms are an essential part of an engine because they ...
Special Order
$5.20
This part includes one manufacturer-sourced carburetor diaphragm. A working diaphragm is an essential component of the engine, as it creates an airtight seal, needed for optimal engine performance. Th...
Special Order
$6.51
Genuine OEM replacement part used on a variety of Engines. This part provides an air tight seal for mounting the Gas Tank. This Gasket is made out of Composite Material and it is Sold Individually. Ov...
In Stock
Order now and your part arrives by Mar 27
$6.51
This is the intake gasket designed for various models of small engine equipment, including blower vacuums. The intake gasket plays a crucial role in internal combustion engines, creating an airtight s...
In Stock
Order now and your part arrives by Mar 27
$6.51
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Plier...
In Stock
Order now and your part arrives by Mar 27
This authentic manufacturer rewind starter spring is a replacement part used in various power equipment engines. It is connected to a pulley system, and it is found inside the starter housing. It is a...
No Longer Available
Genuine Manufacturer Approved replacement part used on a variety of Engines. This is a tube pick-up for 3-5HP horizontal and 5HP vertical engines with 2 and 3 quart tanks and a pulsa jet carburetor. T...
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 082232-0326-01
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from KERNERSVILLE, NC
- Parts Used:
- 493288
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Could not keep an aftermarket muffler on the engine.
Once I determined what OEM muffler I needed, installation was relatively easy. I have a 1982 4hp Briggs on my Snapper tiller. There was a 90* galvanized elbow coming out of the exhaust port, with a bezel nut to lock it down. Do not remove the elbow, even though it appears that you should. If you install the muffler without the elbow the m
... Read more
uffler will parallel the the vacuum for the carburetor and can melt the rubber couplers. Use the elbow to direct the heat away from the carburetor. Use a pipe wrench to lock down the bezel nut because the weight of the muffler, especially under vibration, can work loose and fall down on the tine belt cover and melt it. The bezel nut that comes with the muffler should also be used to lock down the muffler to the threaded intake bracket that comes with the muffler, not to replace the bezel nut for the elbow.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from MUKWONAGO, WI
- Parts Used:
- 272538S
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
no gas to carb
pulled off fuel pump cover ,cleaned surfaces. Applied gasket sealer and replaced fuel pump diaphragm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven C from CENTREVILLE, MI
- Parts Used:
- 495606
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Old diaphragm dried up
Tore carburetor off leaf blower and replaced. To do that require taking off the air cleaner removing the gas tank and all the brackets holding the controls on it. And keeping track of all the screws and Wires that control choke and throttle. I took several photographs. I did not need all the gaskets and jet’s that were included in the ki
... Read more
t but it had what I needed.
Read less
Was this instruction helpful to you?
Thank you for voting!