Models
>
92988-1137-XX
92988-1137-XX Briggs and Stratton Engine
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 92988-1137-XX
Viewing 5 of 5
Keep searches simple, eg. "belt" or "pump".
$6.51
This is an OEM replacement part, sold individually. This Grommet is an elbow for the crankcase breather tube. These rubber elbows were just a convenient way to make a 90 degree bend back when they us...
In Stock
Order now and your part arrives by Apr 9
$7.60
This item is an authentic part that is OEM sourced to ensure quality. The oil seal is intended to be used with small engines from Briggs & Stratton and Toro. This item is used to prevent leaks and to ...
In Stock
Order now and your part arrives by Apr 9
$6.51
This authentic OEM replacement part fits a variety of Toro and Briggs & Stratton engines. An O ring is used to retain pressure between rigid parts. Its flexible material allows it to create a tight se...
In Stock
Order now and your part arrives by Apr 9
$11.16
This item is a genuine replacement part that has been OEM sourced and is intended to be used with lawnmower engines from Briggs & Stratton and Toro. The rubber seal is used to prevent oil from leaking...
In Stock
Order now and your part arrives by Apr 9
In Stock
Order now and your part arrives by Apr 9
$6.51
This is an OEM approved replacement part designed for gas trimmers/brush cutters. Its purpose is to filter out dust and debris from the air that goes into the unit. Over time it will get dirty and clo...
In Stock
Order now and your part arrives by Apr 9
In Stock
Order now and your part arrives by Apr 9
$6.51
This is a genuine OEM sourced part which is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is a standard hardware which may have multip...
In Stock
Order now and your part arrives by Apr 9
$6.51
This is an authentic OEM component from Briggs & Stratton. The magneto armature screw is compatible with many lawn and garden engines. The hardened metal screw helps to mount the magneto armature. A w...
In Stock
Order now and your part arrives by Apr 9
$7.99
This item is a genuine Briggs & Stratton part that has been sourced from the original manufacturer and is intended to be used with small engines. The gasket is used to seal the connection between the ...
In Stock
Order now and your part arrives by Apr 9
$63.68
This replacement armature-magneto is specially designed for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It is an authentic part sourced directly from ori...
In Stock
Order now and your part arrives by Apr 9
$6.51
It is an OEM component which is designed for Briggs and Stratton engines that are commonly installed on a variety of lawn and garden equipment. The cap helps to secure the spring in the pump. Over tim...
In Stock
Order now and your part arrives by Apr 9
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 92988-1137-XX
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from KERNERSVILLE, NC
- Parts Used:
- 493288
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Could not keep an aftermarket muffler on the engine.
Once I determined what OEM muffler I needed, installation was relatively easy. I have a 1982 4hp Briggs on my Snapper tiller. There was a 90* galvanized elbow coming out of the exhaust port, with a bezel nut to lock it down. Do not remove the elbow, even though it appears that you should. If you install the muffler without the elbow the m
... Read more
uffler will parallel the the vacuum for the carburetor and can melt the rubber couplers. Use the elbow to direct the heat away from the carburetor. Use a pipe wrench to lock down the bezel nut because the weight of the muffler, especially under vibration, can work loose and fall down on the tine belt cover and melt it. The bezel nut that comes with the muffler should also be used to lock down the muffler to the threaded intake bracket that comes with the muffler, not to replace the bezel nut for the elbow.
Read less
Was this instruction helpful to you?
Thank you for voting!