Models
>
100902-0110-XX
100902-0110-XX Briggs and Stratton Engine
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 100902-0110-XX
Viewing 2 of 2
Keep searches simple, eg. "belt" or "pump".
$3.99
This is a Genuine Briggs & Stratton part used on 3-5 HP horizontal Pulsa-Jet Carburetor engines (new style). This part is sold individually. Diaphragms are an essential part of an engine because they ...
Special Order
Genuine Manufacturer Approved replacement part used on a variety of Engines. This is a tube pick-up for 3-5HP horizontal and 5HP vertical engines with 2 and 3 quart tanks and a pulsa jet carburetor. T...
No Longer Available
$46.98
This starter clutch is an authentic OEM replacement part used in small outdoor power engines. Each package includes one clutch and one ball bearing. The starter clutch allows the engine to start by en...
In Stock
Order now and your part arrives by Mar 26
$8.30
This item is a genuine OEM sourced part that is intended to be used with small engines from Briggs & Stratton and Toro. The gasket is used to seal the connection between the cylinder and the head. A h...
On Order
$61.15
This magneto provides the spark your engine needs to start and run properly. It’s a durable replacement for a worn coil and installs easily—just set the correct gap and reconnect the wiring for smooth operation.
In Stock
Order now and your part arrives by Mar 26
$7.30
This item is an authentic part that is OEM sourced to ensure quality. The oil seal is intended to be used with small engines from Briggs & Stratton and Toro. This item is used to prevent leaks and to ...
In Stock
Order now and your part arrives by Mar 26
$15.40
This item is available as an individual replacement part but also includes the screws. The muffler deflector attaches to the lo-tone muffler and is made of metal. A nutdriver might be required during ...
In Stock
Order now and your part arrives by Mar 26
$6.25
This is the gasket that helps to provide an air tight seal for the breather assembly. It is a high quality item that is supplied by original equipment manufacturer for use with Briggs and Stratton and...
In Stock
Order now and your part arrives by Mar 26
In Stock
Order now and your part arrives by Mar 26
$6.25
This is an OEM approved replacement part designed for gas trimmers/brush cutters. Its purpose is to filter out dust and debris from the air that goes into the unit. Over time it will get dirty and clo...
In Stock
Order now and your part arrives by Mar 26
$6.25
This is a genuine OEM sourced part which is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is a standard hardware which may have multip...
In Stock
Order now and your part arrives by Mar 26
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 100902-0110-XX
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from ALFRED, ME
- Parts Used:
- 397358
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
5 HP Briggs and Stratton chipper shredder - no spark
Removed old sparkless magneto, replaced with new part PS9278124 Magneto, and still no spark. The only conclusion that I can draw, is this magneto is defective,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from KERNERSVILLE, NC
- Parts Used:
- 493288
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Could not keep an aftermarket muffler on the engine.
Once I determined what OEM muffler I needed, installation was relatively easy. I have a 1982 4hp Briggs on my Snapper tiller. There was a 90* galvanized elbow coming out of the exhaust port, with a bezel nut to lock it down. Do not remove the elbow, even though it appears that you should. If you install the muffler without the elbow the m
... Read more
uffler will parallel the the vacuum for the carburetor and can melt the rubber couplers. Use the elbow to direct the heat away from the carburetor. Use a pipe wrench to lock down the bezel nut because the weight of the muffler, especially under vibration, can work loose and fall down on the tine belt cover and melt it. The bezel nut that comes with the muffler should also be used to lock down the muffler to the threaded intake bracket that comes with the muffler, not to replace the bezel nut for the elbow.
Read less
Was this instruction helpful to you?
Thank you for voting!