Models
>
150202
150202 (0001-B8) Briggs and Stratton Engine
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$7.30
This item is an authentic part that is OEM sourced to ensure quality. The oil seal is intended to be used with small engines from Briggs & Stratton and Toro. This item is used to prevent leaks and to ...
In Stock
Order now and your part arrives by Mar 26
$8.02
This spark plug is an authentic OEM replacement part, it is not an aftermarket equivalent. It is specially made for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equi...
In Stock
Order now and your part arrives by Mar 26
In Stock
Order now and your part arrives by Mar 26
$6.25
This replacement screw is a genuine OEM sourced hardware designed for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It has multiple applications depending ...
In Stock
Order now and your part arrives by Mar 26
This OEM approved overhaul kit is designed for rebuilding/fixing carburetor on a Briggs and Stratton engine. This kit contains all the necessary gaskets, diaphragms and other parts to rebuild your car...
In Stock
Order now and your part arrives by Mar 26
$8.68
This item is a genuine Briggs & Stratton replacement part that has been sourced from the original manufacturer to be used with small engines. The metal key fits into the slot on the crankshaft and ali...
In Stock
Order now and your part arrives by Mar 26
In Stock
Order now and your part arrives by Mar 26
$9.30
The stop switch is made of plastic and metal and helps to turn off the device. This is an authentic replacement part that is sourced from the original manufacturer for use with engines, generators, sn...
In Stock
Order now and your part arrives by Mar 26
$11.36
The crankcase gasket fits between the crankcase cover and the crankcase. This item is available as an individual replacement part and is made out of a thin material. It is a genuine replacement part f...
Special Order
$32.18
This is an authentic Briggs & Stratton replacement part, sourced from the original manufacturer for use with small engines. The special air cleaner cover is commonly used to secure the air filter to t...
In Stock
Order now and your part arrives by Mar 26
$9.90
This high quality replacement part is supplied from original equipment manufacturer for use with Briggs and Stratton engines that are commonly installed on Toro lawn and garden equipment. It is used t...
In Stock
Order now and your part arrives by Mar 26
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dana from HAMMOND, IN
- Parts Used:
- 792006
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Mistreated Briggs & Stratton 206 CC Engine on MTD Chipper
Removed tank and drained old gas.
Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner.
Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again.
Cleaned spark plug electrode.
Reassemble ... Read more d, poured Sea Foam in the bottom of the tank and gave it a few pulls.
Let Sea Foam sit for a while, then filled the tank with Premium.
Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner.
Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again.
Cleaned spark plug electrode.
Reassemble ... Read more d, poured Sea Foam in the bottom of the tank and gave it a few pulls.
Let Sea Foam sit for a while, then filled the tank with Premium.
Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Read less
Was this instruction helpful to you?
Thank you for voting!
Parts fit like a glove
Removed pull start assembly down to the crank. Installed motor housing, motor fan & rewind assembly. All went real good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from N FRANKLIN, CT
- Parts Used:
- 591301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Starter Rewind broke internally-rope did not work
Removed old broken rewind starter (4 bolts); found the Model and Serial numbers; found Parts Direct and ordered new assembly; upon delivery, reinstalled with new Starter and hardware.
Was this instruction helpful to you?
Thank you for voting!