Models
>
MGD5100DC1
MGD5100DC1 Whirlpool Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$6.51
It is important for your dryer to be properly leveled, as an unleveled one can cause excessive vibration and noise when operating, may not drain properly, and can cause excessive wear on various parts...
In Stock
Order now and your part arrives by Aug 20
On Order
$47.14
This kit comes with 2 adhesive pads, 2 brackets and 4 screws. This is for stacking the appliances vertically - dryer over washer.
In Stock
Order now and your part arrives by Aug 20
$43.92
This kit allows you to stack your washer and dryer to maximize your laundry space.
Special Order
$57.30
This stationary drying rack is designed for use in dryers with rear drum dimples spaced 4½ inches apart. Constructed in white, it provides a stable platform for drying items that should not tumble, su...
In Stock
Order now and your part arrives by Aug 20
$73.24
This kit is used for the bottom and side exhaust. The kit includes both the straight and elbow vent.
In Stock
Order now and your part arrives by Aug 20
$68.99
This stacking kit allows compatible front-load washer and dryer models to be stacked vertically. It is designed to maximize laundry space and can be used on various models. Please use your model numbe...
In Stock
Order now and your part arrives by Aug 20
In Stock
Order now and your part arrives by Aug 20
In Stock
Order now and your part arrives by Aug 20
$49.29
This Dryer Drying Rack attaches to the inside of the dryer drum and remains stationary as the dryer turns so you can dry shoes, sweaters and other items that shouldn't be tumbled. This accessory can b...
In Stock
Order now and your part arrives by Aug 20
$17.44
This seal creates a tight barrier to prevent air or moisture leaks during operation. A proper seal improves efficiency and maintains consistent internal conditions. Replacing a worn seal reduces energ...
In Stock
Order now and your part arrives by Aug 20
The actual physical measurement of this part is 23 3/4 inches and has a 2 1/2 inch clearance. If there is any excess length, it can be trimmed to fit according to your specific needs.
In Stock
Order now and your part arrives by Aug 20
Common Problems and Symptoms for MGD5100DC1
Viewing 3 of 3Noisy
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Tenino, WA
- Parts Used:
- W11581317
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
converting to LP gas
First I removed the front panel which allowed access to the burner assembly. Then I removed the gas connector and elbow from the back of the dryer. Then I removed 2 screws that hold burner assembly in place and 2 screws that hold an angle brace for the burner assembly. Had to loosen the screw that clamps around the gas pipe holding it in
... Read more
place clear in the back inside dryer housing. Unplugged all wiring connectors, then I removed the burner assembly and removed the 2 screws holding the burner tube to the valve. Remove the orifice and replaced with the proper size for LP gas. Then removed the blocking pin and replaced with one for LP gas. Then reassembled in reverse order. Actually pretty easy.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from San Diego, CA
- Parts Used:
- W10470674
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Needed to change rear exhaust to the side to fit dryer into my closet.
First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Brentwood, CA
- Parts Used:
- 8541503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Placing Dryer on Top of Washing Machine with Stack Kit
I purchased a stack kit from "Part select.com". The item was just what I needed to do the job. The delivery of the part was made the next morning. WOW! Excellent service! The process was completed in less than 24 hours, start to finish. Very impressed!
Was this instruction helpful to you?
Thank you for voting!