Models
>
MGD3100DW0
MGD3100DW0 Whirlpool Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$6.51
It is important for your dryer to be properly leveled, as an unleveled one can cause excessive vibration and noise when operating, may not drain properly, and can cause excessive wear on various parts...
In Stock
Order now and your part arrives by Aug 20
$27.83
If your dryer is not tumbling, will not start, or is excessively noisy while operating, there may be an issue with your idler pulley. The idler pulley works by maintaining a constant tension on the dr...
In Stock
Order now and your part arrives by Aug 20
In Stock
Order now and your part arrives by Aug 20
$50.36
The blower wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. The blower wheel, which is usually plastic, may wear out over ...
In Stock
Order now and your part arrives by Aug 20
On Order
$47.14
This kit comes with 2 adhesive pads, 2 brackets and 4 screws. This is for stacking the appliances vertically - dryer over washer.
In Stock
Order now and your part arrives by Aug 20
$43.92
This kit allows you to stack your washer and dryer to maximize your laundry space.
Special Order
$57.30
This stationary drying rack is designed for use in dryers with rear drum dimples spaced 4½ inches apart. Constructed in white, it provides a stable platform for drying items that should not tumble, su...
In Stock
Order now and your part arrives by Aug 20
$73.24
This kit is used for the bottom and side exhaust. The kit includes both the straight and elbow vent.
In Stock
Order now and your part arrives by Aug 20
$82.21
This door hinge assembly supports your dryer door, allowing it to pivot open and closed. If the door becomes difficult to open, replacing this genuine OEM part will restore smooth operation. Be sure t...
In Stock
Order now and your part arrives by Aug 20
$68.99
This stacking kit allows compatible front-load washer and dryer models to be stacked vertically. It is designed to maximize laundry space and can be used on various models. Please use your model numbe...
In Stock
Order now and your part arrives by Aug 20
In Stock
Order now and your part arrives by Aug 20
Common Problems and Symptoms for MGD3100DW0
Viewing 8 of 8Noisy
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Door Sags
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Burning smell
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Tenino, WA
- Parts Used:
- W11581317
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
converting to LP gas
First I removed the front panel which allowed access to the burner assembly. Then I removed the gas connector and elbow from the back of the dryer. Then I removed 2 screws that hold burner assembly in place and 2 screws that hold an angle brace for the burner assembly. Had to loosen the screw that clamps around the gas pipe holding it in
... Read more
place clear in the back inside dryer housing. Unplugged all wiring connectors, then I removed the burner assembly and removed the 2 screws holding the burner tube to the valve. Remove the orifice and replaced with the proper size for LP gas. Then removed the blocking pin and replaced with one for LP gas. Then reassembled in reverse order. Actually pretty easy.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from cheswick, PA
- Parts Used:
- WP697772
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
craked blower motor
somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from San Diego, CA
- Parts Used:
- W10470674
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Needed to change rear exhaust to the side to fit dryer into my closet.
First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.
Was this instruction helpful to you?
Thank you for voting!