Models
>
NED4705EW1
NED4705EW1 Whirlpool Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$59.43
Sourced directly from the manufacturer, this heating element is an OEM approved replacement part for a variety of dryers and is sold individually. It measures approximately 10.5 inches long, 7.5 inche...
In Stock
Order now and your part arrives by Aug 21
$48.21
This thermal cut-off kit is for a dryer and is sourced directly from the manufacturer. The thermal cut-off is a safety mechanism that is designed to trip if your dryer is at risk of overheating, to pr...
In Stock
Order now and your part arrives by Aug 21
$46.07
Sourced directly from the manufacturer, this OEM approved replacement handle is approximately 6 inches long, 2 inches wide, and is made of durable white plastic. This handle is used to open the dryer ...
In Stock
Order now and your part arrives by Aug 21
$6.51
It is important for your dryer to be properly leveled, as an unleveled one can cause excessive vibration and noise when operating, may not drain properly, and can cause excessive wear on various parts...
In Stock
Order now and your part arrives by Aug 21
$35.34
The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.
In Stock
Order now and your part arrives by Aug 21
$22.91
If your dryer door keeps popping open or won’t latch, this door catch might be the fix you need. It’s a small part, but it plays a big role in keeping your dryer running smoothly. Just swap out the ol...
In Stock
Order now and your part arrives by Aug 21
$55.18
This is a genuine OEM replacement door gasket for your dryer. The gasket, also known as a door seal, is used to provide an airtight seal when the dryer door is closed. If the gasket has failed it can ...
In Stock
Order now and your part arrives by Aug 21
$57.30
This stationary drying rack is designed for use in dryers with rear drum dimples spaced 4½ inches apart. Constructed in white, it provides a stable platform for drying items that should not tumble, su...
In Stock
Order now and your part arrives by Aug 21
$9.79
This control knob is for dryers.
Control knob lets you control cycle settings.
Remove the knob by pulling it straight off its post.
In Stock
Order now and your part arrives by Aug 21
In Stock
Order now and your part arrives by Aug 21
$59.43
This terminal and wire kit helps repair electrical connections in your dryer by replacing worn or damaged wires. It includes wires, screws, and wire nuts, but the terminal block is sold separately. Us...
In Stock
Order now and your part arrives by Aug 21
$20.72
Door catch bezel fits into the door catch on the front panel and prevents the door strike from scratching the panel.
In Stock
Order now and your part arrives by Aug 21
Common Problems and Symptoms for NED4705EW1
Viewing 11 of 11Not Heating
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Too hot
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Door Pops Open
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Heat stays on after drum has stopped
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Timer Not Working
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gadi from Irvine, CA
- Parts Used:
- 279838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dryer motor runs, but no heat
To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.
To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.
You can check the heating element wi ... Read more th an ohm-meter or visually inspect it to see if the heating element spiral wire is broken.
Don't hurry to dispose the old element. My model includes a small electric safety part. You'll need to transfer it to the new heating element (that comes without it)..
Good luck.
To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.
You can check the heating element wi ... Read more th an ohm-meter or visually inspect it to see if the heating element spiral wire is broken.
Don't hurry to dispose the old element. My model includes a small electric safety part. You'll need to transfer it to the new heating element (that comes without it)..
Good luck.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vernon from Niceville, FL
- Parts Used:
- 279816
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No Heat
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back
... Read more
off.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Remie from Mahopac, NY
- Parts Used:
- 279838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dryer would run with no heat.
The repair was easy. the most time consuming part was vacuuming the dust from the back of the Dryer, The repair required removing screw from the back panel of the dryer. Then removing screws from the heating element and unplugging the wires. The only moderately diffculy part was swapping the sensor form the old element.
Was this instruction helpful to you?
Thank you for voting!