DVE52M7750AV (A3) Samsung Dryer - Instructions

I YouTube it and there’s a step by step process on how to do it, took maybe 30 mins. If I can so can you

Cleaned the sensors from inside the drum with alcohol and that did not work. Ordered two sensors. Lift top cover. Remove screws on each of the front side that secures front cover. Unplug door sensor and pull front cover towards you and lift at same time removing from frame. I own dogs and immediately noticed dog hair and surprisingly lint all over the place. Remove the screws from the lint trap. (Theres one you access from inside the drum.) Unplug your sensor wires. Remove lint trap. The sensors simply push in/out. While I was in there I removed the cover for the lint tube and cleaned it out good. Lint had started to gather around the fan. Reverse your process and your done. TIP: Keep your screws orderly as you unscrew them. If you have this problem, just a good cleaning of hair, lint, dirt may do the trick as it essentially packs around the plug of the sensors. I had already ordered my sensors so I just put them in. I took my time and cleaned good and it was about an hour. It could be done in 15-30 minutes easily.

I ordered twice from this site. the thermistor was the first order, the fuse was the second order. Turns out the thermistor sent was the WRONG one. When I reassemble the dryer, after 20 minutes the thermistor sent burned up to a crispy chard. The ohms on the wrong part was 12ohms. per the dryer diagnostics the thermistor should have been =<1 ohm. I put in the original part and it worked. The fuse did the trick. the thermistor, not so much. Lesson to be learned is to not rely on this sites parts compatibility information. Look at the specs for your dryer from the manufacturer.

Samsung had no servicers available, after over 3 months calling and sending photos and signing papers they sent a refund. Never any advice on repair from Samssung. Saw a video by JEFF OSTIROFF that lfor disassembly and location of heating parts. Gor $40 Samsug service manual that was rather useless. Disassembled and tested thermostat, Thermistor, and heat element. Appeared that HI-HEAT thermistor was open circuit all others OK. Sent for new one, arrived damaged insufficientlyb packed Tested original again out of appliance, tested OK. Got replacement for damaged thermistor and put it in, reassembled and IT WORKED! Notvsure if original thermistor was intermittant, or connection problem was the fault.

I pretty much followed the provided videos, but didn't remove the drum. That seemed a bit much. I was able to get the heating element out, and replace the Thermal Fuse and Thermostat. Dryer runs and heats like a top now!

A month prior to this repair, I took the dryer apart, cleaned the clogged lint out, and replaced the thermistor with a cheap aftermarket part. It lasted a month. Bought this more expensive OEM thermistor, hopefully of a better quality. Realized that I could have gotten to the thermistor from the back by simply removing the vent pipe and carefully reaching through the vent pipe hole to take out the thermistor. Did that this time instead of taking everything apart. Also bought an updated lint screen (aftermarket part). It has better mesh although it doesn't fit quite as perfectly as the original. So we'll see if the OEM thermistor lasts longer. The repair time was mostly spent moving the washer and dryer within a fairly small laundry room. The air lifter really helps.

NECESSARY REQUIREMENTS TO DISMANTLE AND TAKE OFF DRYER CASING USING SCREWDRIVER AND NEEDLE NOSE PLIERS TO REPLACE THERMAL FUSE LOCATED ON THEHEATING ELEMENT CASING.TOOK ME HALF HOUR REPLACED PART AND PROCEDED TO PUT EVERYTHING BCK IN PLACE.PLUGGED BACK INTO SOCKET .whalla IM UP AND RUNNING AGAIN.DIFFICULTY RATING 1 TO 10-3.thanks 4 your support this was not difficult or hard just required TIME & PATIENCE. Thank u once again.THIS SITE IS THE GREATEST.

I originally called a repair person to come out but that was a total waste of time and money. He removed the front of the dryer claimed there was a dryer sheet causing the problem and put it back together.
Never again!
I watched a youtube video for step by step instructions on how to take the dryer apart.
I took the front door of the dryer off, removed the filter cover and the dryer drum & belt. Removing this was simple and allowed me to see everything I was working on. With the new part in hand, I removed one wire at a time from the non working heat sensor and connected it to the new part. That way I was sure I had the right connections.
I then removed the thermostat making sure to put the new one back in place exactly as the old one.
I then put the drum back in place with the belt securely fastened. I put the cover back on the lint filter and placed the dryer door back on securing it in place. The dryer is now working perfectly. It takes longer to take the dryer apart than to replace the old parts.

*** Unplug Dryer ***
Spent years (PITA) trying to figure out how to do this repair.

About 2 weeks ago I came across this U-Tube video.
This video really saved the day and I cannot tell you how much I appreciate this guys video.

Here is the link to an awesome video.
https://www.youtube.com/watch?v=6u1_gnJAQ5U

Tip: It may help some of you to bring up this video on your phone or laptop to reference as you do the repair.

Good luck
M

Followed the video on the website and finished it in a short time. Now it works like a new dryer.

Follow the video instructions.

I had to take the whole thing apart to replace the drum wrapper. I followed this very helpful YouTube video for the step-by-step instructions on disassembly.

https://www.youtube.com/watch?v=9ul2BIvVEVU&t=428s

Once the new drum was installed, I followed the steps in reverse to put everything back together.

Unplugged the dryer for safety. Unattached top of dryer from door with putty tool. Took front of dryer off. Unplugged door. Took off bracket to heating element case. Pulled out case. Replaced the thermostat. Then put all back together and tested the dryer. Works like a charm.

Thank you
partselect.com for a much better heavy duty belt than the original. Way over priced, but well worth it. After watching the video & following it step-by-step, I now have a perfectly running dryer. P.S. don't forget to plug back in the (3) wire harnesses. The entire experience was a great feeling of accomplishment. Thanks again partselect.com

Opened the dryer door, removed the old filter and replaced it with new filter.