Models
>
MEDB835DW3
MEDB835DW3 Maytag Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for MEDB835DW3
Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
$38.06
The Whirlpool Dryer Repair Kit is a genuine OEM maintenance kit designed to resolve common issues such as squeaking, thumping, or poor drum rotation in 27-inch dryers. This all-in-one kit is compatibl...
In Stock
Order now and your part arrives by Mar 22
$18.85
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. This part is sold separ...
In Stock
Order now and your part arrives by Mar 22
$26.20
Often referred to as a dryer belt tension pulley wheel, this idler pulley is an OEM approved replacement part for a variety of dryer models. The idler pulley puts tension on the drive belt, and if the...
In Stock
Order now and your part arrives by Mar 22
The internal-bias thermostat, also know as a thermistor, is used to prevent the dryer from overheating. It does this by monitoring and controlling the temperature of the inside of the dryer drum. If ...
In Stock
Order now and your part arrives by Mar 22
$11.50
This small but mighty OEM piece is called a tri-ring and is used to support the drum roller shaft and the idler pulley shaft in your dryer. It helps to provide a tight seal between components by evenl...
In Stock
Order now and your part arrives by Mar 22
$6.25
It is important for your dryer to be properly leveled, as an unleveled one can cause excessive vibration and noise when operating, may not drain properly, and can cause excessive wear on various parts...
In Stock
Order now and your part arrives by Mar 22
$26.73
If your dryer is not tumbling, will not start, or is excessively noisy while operating, there may be an issue with your idler pulley. The idler pulley works by maintaining a constant tension on the dr...
In Stock
Order now and your part arrives by Mar 22
This heating element connection wire kit is a genuine OEM replacement for your electric dryer. The kit is used to connect the thermostat to the heater element. The kit comes with a yellow wire nut and...
In Stock
Order now and your part arrives by Mar 22
$7.30
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order now and your part arrives by Mar 22
$22.00
If your dryer door keeps popping open or won’t latch, this door catch might be the fix you need. It’s a small part, but it plays a big role in keeping your dryer running smoothly. Just swap out the ol...
In Stock
Order now and your part arrives by Mar 22
$11.50
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
In Stock
Order now and your part arrives by Mar 22
$7.30
This is a multi-use screw mostly used in dryers. It has a diameter of #10, length of one inch, and thread size of 16. Remember to follow safety practices and instructions provided in the manufacturer ...
In Stock
Order now and your part arrives by Mar 22
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Thomas
October 12, 2021
Can you send me, or direct me to, a key to the parts as numbered on your diagrams (i.E., parts 1, 2, 3, etc., as shown on the diagrams, not the full part numbers). Thanks! Tom
For model number MEDB835DW3
Hello Thomas, Thank you for the question. All the parts are listed on the site. Just click the diagram and you will get a split screen. The top is the diagram and the bottom is the parts list. If you need number 3, just scroll down to the list until you see number 3. Click on the part and you will come to the page with part details and part numbers. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jason
November 27, 2023
I had a Sox get into the blower housing because it was ran without the lent basket . How do I access the blower below the lint basket. By pins on each side of cabinet or through the top head unit
For model number MEDB835DW3
Hi Jason, thank you for your question! You will need to remove the screws behind the control panel. So you can pop the top off. After removing the both panels from the back, you can view the top panel hinges screws, remove those screws. After removing the top panel screws from the back, push the top panel back towards the wall. It will free up and you can lift up. After lifting the top panel, you will see the screws to remove the front panel. Unplug the wiring harness. Open the door and remove the screws from the front. After that you can pull the front panel and remove it to access the blower wheel housing. After removing the blower housing screws, you can access the blower wheel. We hope this information helps!
Was this helpful?
Thank you for voting!
Greg
February 11, 2024
Maytag Bravos Xl modle #MEDB835DW3. I have correct voltage at receptical and at dryer pigtail. My question is, why do I have diagnostic code F4E4 stating low voltage?
For model number MEDB835DW3
Hello Greg, Thank you for writing. This could be a issue with the Power Cord or the wiring for the appliance. We suggest testing the wiring including the heating element wiring and checking for any wear or damage. We hope this helps!
Was this helpful?
Thank you for voting!
Common Problems and Symptoms for MEDB835DW3
Viewing 10 of 10Noisy
Fixed by these parts
How to fix it
Not Heating
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Too hot
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Door Pops Open
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- jason from HOLDEN, MA
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
very loud squeeling sound
The issue was the idler pulley. First I began opening up the front panel based on a youtube video but soon realized the model was slightly different and required a lot more items to remove. I saw the pulley in the back with nothing in the way so I put the front panel crap back on and removed the rear panel. There it was, very simple to re
... Read more
move and replace. I'm not looking forward to drum rollers though. Hopefully they're aren't as difficult as they appear.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eddie from PELZER, SC
- Parts Used:
- 4392067
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Squeaky Dryer Noise
I purchased the dryer repair kit with the drum belt, wheels and idler pulley. I watched the instructional videos online and it seemed fairly straight forward. Breaking down the dryer and replacing the pulleys was easy enough. My problem began when I tried to feed the drum belt around the idler pulley. After finishing the job, the dryer wo
... Read more
uld not turn and the sensor light stayed on. I thought something else was broken with the dryer and spent hours trouble shooting other problems that I was having. Finally I figured out that the drum belt was not installed correctly around the idler pulley. However, I could not get it properly installed from the front of the machine so I tried from the rear still with no avail. I finally had to fish the old belt out of the garbage can that I had thrown away earlier. I lined up the old belt with the new one in the kit and discovered that the new belt was much smaller, so I put the old one back on the drum. Here's the lesson I learned...make sure the belts are the same size before attempting to install. The old idler was responsible for the squeaking and that stopped but I am still using the same old drum belt. Hope it lasts.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GREGORY from Wilsonville, OR
- Parts Used:
- 279640
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Very Loud Squeaking Noise
1) Disconnected power cord from wall. 2) Disconnected vent hose from back of dryer. 3)Removed dryer rear panel. 4)Disengaged tension spring on idle wheel arm. 5) Removed worn idle wheel. 6)Installed new Idler wheel assembly. 7) Vacuumed dust from rear of dryer (optional, recommended). 8) Reinstalled rear cover, vent hose and power cord. E
... Read more
asy repair 15-30
Read less
Was this instruction helpful to you?
Thank you for voting!