This OEM dryer door switch is an on/off mechanism that detects when the door is open to prevent the dryer from operating. If your dryer will turn on but will not start or continues working while the d...
In Stock
Order within the next 5 hrs and your part ships today!
When connected to electricity the dryer heating element glows red hot and generates heat. When air is blown over it, it heats the air which is used to dry the clothes. The heating element fits inside ...
In Stock
Order within the next 5 hrs and your part ships today!
Often referred to as a dryer belt tension pulley wheel, this idler pulley is an OEM approved replacement part for a variety of dryer models. The idler pulley puts tension on the drive belt, and if the...
In Stock
Order within the next 5 hrs and your part ships today!
If the lint filter in your dryer has become damaged and unusable, it is important to replace it as soon as possible. The filter traps lint and other debris from your laundry, keeping it out of your ai...
In Stock
Order within the next 5 hrs and your part ships today!
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the d...
In Stock
Order within the next 5 hrs and your part ships today!
This small but mighty OEM piece is called a tri-ring and is used to support the drum roller shaft and the idler pulley shaft in your dryer. It helps to provide a tight seal between components by evenl...
In Stock
Order within the next 5 hrs and your part ships today!
The internal-bias thermostat, also know as a thermistor, is used to prevent the dryer from overheating. It does this by monitoring and controlling the temperature of the inside of the dryer drum. If ...
In Stock
Order within the next 5 hrs and your part ships today!
It is important for your dryer to be properly leveled, as an unleveled one can cause excessive vibration and noise when operating, may not drain properly, and can cause excessive wear on various parts...
In Stock
Order within the next 5 hrs and your part ships today!
This thermal cut-off kit includes a genuine OEM replacement high limit thermostat and a fuse. The thermostat is a safety device used to prevent the dryer from overheating, and the fuse serves as a bac...
In Stock
Order within the next 5 hrs and your part ships today!
If your dryer is not tumbling, will not start, or is excessively noisy while operating, there may be an issue with your idler pulley. The idler pulley works by maintaining a constant tension on the dr...
In Stock
Order within the next 5 hrs and your part ships today!
This is an authentic OEM replacement moisture sensor for your dryer. The sensor detects the moisture levels in your clothing while the appliance is operating, and once the appropriate level has been r...
In Stock
Order within the next 5 hrs and your part ships today!
This heating element connection wire kit is a genuine OEM replacement for your electric dryer. The kit is used to connect the thermostat to the heater element. The kit comes with a yellow wire nut and...
In Stock
Order within the next 5 hrs and your part ships today!
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
6 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gabrielle
July 21, 2022
Dryer was not heating, so purchased a heating element kit. I replaced the heating element and all fuses attached. All wires were lined up for the appropriate part. Then i decided to vacuum out before i finished, which caused the wires to get mixed up. I know which wires attach to the element itself. But do not know the remainder of the wiring pattern and cannot find it anywhere. Can anyone advise of how wiring should be connected?
For model number MEDB765FW0
Hi Gabrielle,
Thank you for your question. We have included a link to one of our YouTube videos that you may reference on how to install the heating element. The dryer in the video may appear different from yours, but it will give you a general idea on how to install the part. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Keith
November 24, 2021
How do I take the top and front panel off
For model number MEDB765FW0
Hello Keith , Thank you for the question. We have attached a video that will show how to open up the cabinet. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Jeremy
July 18, 2023
Check lint screen light stays on dryer will not turn on
For model number MEDB765FW0
Hi Jeremy, thank you for your question! If the light continues to stay on, clean the lint screen, or check the venting going to the outside and verify that it is clear. If this does not help, check that you have the proper voltages to the dryer- 220 and 110. If that checks fine, then take off the top and make sure the belt is on. If that is fine, then access the thermal fuse, part number FIX11766766, on the blower housing and see if it is closed or open. We hope this solves your problem!
Hello Mikki, Thank you for the question. We have attached a link to the How to Video for installing the Heating Element. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Check Lint screen light stays on but dryer will not come on. I have reached out to you guys and you told me what to check everything is good. The thermal fuse beeps when I use my Ohm meter the outlet thermistor Ohm reading goes down when I heat it up.What else should I check thanks
For model number MEDB765FW0
Hi Jeremy, thank you for getting in touch. Since you have checked the most common parts that might cause this issue, you may need to check the electronic control board, part number FIX12074540, as it is most likely faulty and may need to be replaced. We hope this information helps!
Pryed dryer top open and opened front door. . Unscrewed the 2 retaining screws. Pulled old switch from the wiring harness. Put new switch in place and replaced the retaining screws. Put new switch wire plug into the wiring harness. Before closing top, checked door switch function with dryer on. Dryer cut off when door open an
... Read mored when closed dryer started normally. . . Maint. Note instruction book should warn that letting door slam, which I did on occaision, broke the switch arm. Might save future problems.
Remove the kick plate from the bottom of the dryer by sliding a putty knife along the top edge to release the plastic clamps, one on each side about 4" in from the edges. The kick plate folds out and down. You will see the heat shield on the right, held in by one hex head screw. Remove screw and heat shield. The element is positioned in a
... Read moren open-front housing and is fastened to the left side of the housing by two hex head screws, located on the "rail" of the element and right near the two wires. Remove the hex-head screws that hold the element in place and disconnected the two wires by pulling them out by hand or with needle nose pliers. The only difficulty here is the cramped working area...I recommend a stubby socket driver for these two screws. Most of this I had to do by feel because I could not see the screw heads. Once the screws are out and the wires have been disconnected, slide the old element straight out toward you. You may need to disconnect a small plastic hose located to the left front of the element, but this hose just pulls right off. Vacume the dust & lint build-up out of the whole area, wipe out the element housing and clean up the whole underside of the dryer prior to installing the new element. Installation is reverse of removal. It also might be a good opportunity to clean out your exhaust duct and the vent to the outside. (Never use the aluminum foil-accordian-type duct.) If the exterior dryer vent has any kind of screen over it, remove it and get rid of it. Screens collect lint, lint builds up and burns out elements.
