YMED6600TQ0 Maytag Dryer - Instructions

First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back off.

I basically took the back offo the drive, then detach
the heating coil. Afterwards had to go back in and
change the thermal regulator an the job was completed.

Grow a second set of hands. Always unplug any appliance. Remove lint screen. remove two screws (philips Head). I took a wooden shim lightly tapped w/hammer to pop front of dryer top free. Mine worked on hinges and just flipped back til it rested against the wall. Removed two 5/16 screws inside holding face on carefully raise face section off the support clips at either side on the bottom. Pull drum out (I have the large style drum commercial size [approx.). Clean the inside free of all lint (known to be fire hazard). Sling new belt around drum. Get newly grown set of hands to hold drum in place. Pinch belt to fit between tensioner, lift tensioner and place belt around motor pulley. Spin drum couple times to make certain belt isn't twisted. Reverse dismantle proccess to put back together. Replace all parts that come with kit, you'll feel better knowing you got a new dryer, almost.

unpluged the dryer, removed the back panel, I examined the heating coil, it seemed unbroken, so I used a amp meter to test the various sensors. Found the upper thermal sensor was bad, looked up the part and ordered it, had to get the thermal cut off kit to get the sensor I needed. Installed it no problem, put the back back on, and it worked great.

After a few years of slamming the dryer door (at least that is what my husband says), the catch on the dryer door broke. Using pliers (I used needle nose) squeeze the outer edges of the catch together (vertically). With it compressed, it should slide out easily. My husband had jacked with ours prior to the repair, so the broken piece in the door was actually sideways and would not fit through the hole. Using a screwdriver, I pushed that piece into the door (it lives in the door somewhere now). I was then able to slide out the rest of the old catch. Compress the new catch and insert it into the hole in the door. Push it in until it clicks into place. DONE! Happy Drying!

couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw! Just for fun, I put the motor in a bench vise and got the wheel hub off (in pieces). VERY tight! Ordered new wheel, and the job was smooth sailing from there on. I am guessing that experienced repair people automatically order the motor and blower wheel at the same time(?) BTW both parts were perfect matches for the originals. Not surprised; this has always been my experience with partselect.com!

1st Unpluged power.
2nd removed two screws under lint screen cover.
3rd poped up lid with flathead screwdryer, then removed (2) 5/16 screws from door cover and unpluged lid switch, lifted up dryer door pannel
4th removed drum
5th took out plastic triangle wheel rings
6th removed old belt guild (to motor pully)
7th removed old wheels and plastic rings stops
8th cleaned excessive hair dust with shopvac
9th put new replaicment part in dryer. made sure to turn manually to make sure belt was lined up properly, then put all dryer peices back.
10th aditional work, took back cover off and removed the (4) 1/4 screws for lint screen case (left side in dryer) vacumed out any excessive dirt lint ect, also cleaned any excessive dust I found in back of dryer, dryer , exhaust ect, and put all back together.
JUst like a new dryer aain after all PM was complete.

1. disconnect power,gas and vent lines
2. pop off top of unit
3. remove front of dryer
4. lay unit on its back
5. remove drum and replace pulley assembly,belt,drum rollers of which it has 2 rear and 2 front
6. reverse above and then remove filter-vent housing and scrape off old seal install new seal
7. re-connect power,gas and vent use again
8. only sad part to whole job was seeing how cheaply whirlpool now makes thier products

Great! Spent about $36.00 and I ended up with a overhauled dryer. I ended up cleaning the whole thing out, it's amazing how much stuff accummulates in the frame of a dryer, I also found about $2.00 in change. It's a good idea to clean out a dryer every few years and the broken belt forced me to do it.
But anyway the parts cam very quick and had easy to follow directions.
I would reccomend part select. Matt

super fast shipping, got the part in two days, and had it done in 15-20 min, remove the front pannel, remove the belt and tenssioner,took the drum out , took the old rollers , lubed the shafts,replaced the old rollers with the new ones, intalled the drum back, the tenssioner and the new belt, reinstalled the front pannel, and done...easy and fast job, like new dryer, works nice...save some money...the new one will do the same..just dry the clothes.

The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair.

Pryed the top off the dryer, unplugged the door switch, took the screws out of the front panel, then lifted the drum out. Placed the new belt around the drum and while my wife held it in place and steadied it, I reached underneath and looped the belt through (as per instructions), reassembled and back in business! Reaching under the drum was not that easy....VERY tight space to work in and there was no way I could get both hands through, I almost gave up, but one last try and a couple of good grunts, and it popped into place. Getting the wires back on the door switch was a bit of an ordeal too. Took about 30 mins. but still worth it. I'm sure I saved at least a $100 repair.

I took a ¼ inch nut driver and removed the rear cover from the unit, and then used a continuity tester to determine which safety device was open. According to the schematic there was one non-resettable safety device in the heating circuit, and that was open. The kit that I ordered came with thermal cutoff and a thermostat. I replaced both parts and the unit now operates normally. While I had the dryer open I thoroughly cleaned the dust and lint from the unit and also the 4 inch vent pipe. I ordered this part on Friday morning and received it early Saturday afternoon.

It was really quite esy remove the screws from the back and pop the top off . then remove 2 top inside screws from the front , lift the front off the sides , support the drum and lift out , you will then see the idler wheels, replace them with the new ones ,replce the tensioner , wrap the belt around the drum, need help putting the drum back in the case, have someone hold the drum in place while you lay on the ground and put the belt around the motor pulley and the tensioner on the bottom.you then put the front panel back into place and secure with the 2 inside screws, then put the rest back together in reverse oder. ... hope this helps someone

First my son and I moved the dryer to the garage as we believed there would be a lot of lint possible during disassembly. Used a flat head screwdriver to pop the top from dryer housing. Then removing 2 nuts to facilitate the removal of the front of the dryer. The drum was able to be removed to diagnose the offending drum roller wheel. The drum roller wheel has experienced a failure as it had melted off of the metal spacer. Removing it and replacing with the new one was pretty easy. We then used a shop vac and an air hose to clean out all the lint, coins, paper clips and lost jewelry. Surprisingly there was not a single sock in there. Put it all back together in reverse order and plugged it in and now spins like a dream.