Models > 48231010030

48231010030 (DLGX2802R) LG Dryer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for 48231010030

Viewing 4 of 4
Keep searches simple, eg. "belt" or "pump".
The drum roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter...
In Stock
The Dryer's Lint Filter is used to collect lint during the dryer cycle as it passes through the dryer vent, in order to prevent damage to the machine. This manufacturer-approved part comes in gray, me...
In Stock
This genuine OEM sensor is also known as a moisture sensor or a humidity sensor. It is found underneath the lint filter in your dryer, and is used to detect the amount of moisture present in the drum....
In Stock
This is an authentic OEM housing for the lint filter in your dryer. This plastic cover helps to protect the actual lint filter, as that part is more delicate. It is important to have a functioning lin...
In Stock
If the drum in your dryer will not tumble, or it is noisy while operating, there may be an issue with the drum belt. The belt is found looped around the dryer drum, a tension pulley, and a motor pulle...
In Stock
In Stock
$42.84
This is a replacement lint screen guide for your dryer. The lint screen guide attaches to the front bulkhead and supports the lint screen. If your lint screen will not stay in place, or if you are not...
In Stock
$104.55
Comes with bracket and wire harness.
In Stock
No Longer Available
$33.91
In Stock
$9.88
In Stock
This plastic adjustable dryer leg is used to support the weight and adjust the height of your dryer to keep it level. To install the leg, tip the dryer back and screw it into the bottom of your dryer ...
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for 48231010030

Viewing 4 of 4
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Marks left on clothes
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing Fixing
How to fix it
Leaking
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
  • Customer:
    Mark from WAVERLY, OH
  • Parts Used:
    AGM75510755
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable), Wrench set
Dryer making a thumping and squealing noise when running
Had to replace front drum support rollers. Removed screws underneath top in back that held bracket that keeps top in place. Slid top towards rear and lifted up. Removed 4 screws that hold plastic front panel in place (inside..2 on each corner) Unplugged front panel electric plugs to remove panel. Opened door..removed 2 screws at bottom of door opening. Removed screws on top of front panel. Unplugged door switch plug. Removed front panel. Removed right front roller with 9/16th wrench for nut. Adjustable for back of stud. Lifted up on drum to get roller out. Reversed to install. Left roller a bit harder to get to stud. Removed and installed same as right side. Did not attempt to replace rear rollers. Have them if needed but very much more involved to replace.
69 of 83 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    David from Annapolis, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Filter parts chipped - replaced
Removed existing parts using screwdriver, positioned new parts in dryer and re-inserted screws, tightened - done. Piece of cake, even for someone who cannot saw a straight line with a chop saw.
47 of 82 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    CAROL from NAMPA, ID
  • Parts Used:
    4581EL2002H
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers
Screeching during operation
Found disassembly video and watched several times. Suspected that one of the drum wheels had seized up. Found extreme volume of lint and hair inside unit as well as a dryer sheet melted on top of heating unit. Front left drum wheel was worn down from lint and hair jamming its movement. Video made it easy, not a really complicated piece of machinery. Replaced all 4 wheels due to normal wear on other three. Wanted to be sure drum evenly balanced on all 4. Parts came quickly and were easy to install. My sister and I did this together. Would not recommend doing it alone. Took time to vac and wipe down entire unit. Now it runs so quiet we have to look to see if it is operating. Got a brand new machine out of it, saved a couple of hundred dollars in repair bills, and found 11 cents inside the machine. For your own piece of mind, if you have had your dryer for several years, you need to open it up and clean it out. Its not hard... added note, we are both in our 60's... so if we can do it so can you.... Such a feeling of accomplishment, can't buy that in a store....
28 of 36 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!