DLGX5102W (ABWEEUS) LG Dryer - Instructions

Found disassembly video and watched several times. Suspected that one of the drum wheels had seized up. Found extreme volume of lint and hair inside unit as well as a dryer sheet melted on top of heating unit. Front left drum wheel was worn down from lint and hair jamming its movement. Video made it easy, not a really complicated piece of machinery. Replaced all 4 wheels due to normal wear on other three. Wanted to be sure drum evenly balanced on all 4. Parts came quickly and were easy to install. My sister and I did this together. Would not recommend doing it alone. Took time to vac and wipe down entire unit. Now it runs so quiet we have to look to see if it is operating. Got a brand new machine out of it, saved a couple of hundred dollars in repair bills, and found 11 cents inside the machine. For your own piece of mind, if you have had your dryer for several years, you need to open it up and clean it out. Its not hard... added note, we are both in our 60's... so if we can do it so can you.... Such a feeling of accomplishment, can't buy that in a store....

I noticed the flame would start, then quit after about 15 seconds. I checked the flame detector, and found the lenze cracked. I replaced it, and it's as good as gold.

It looked like a hard job to take the drum out to get at the part. But the top was off with 3 screws, the front about 6 I think. Then the front frame, only 4 screws. I think setting the belt tentioner was the hardest thing to do.

Done in 45 minutes, both the job, then the next load of laundry.

I followed a Repair Clinic Urube video except the video had a model with the controls in front and my dryer has the controls on a back panel. The difference was in how to get the top of the dryer off after removing all the screws. The video
said to push back on the top panel which did not work because of the back controls. Instead I had to push up on the front to release it and then push back. The rollers were also in a slightly different place but were easily found and replaced. The dryer is now back to normal.

The first thing I did was locate a copy of the Service Manual (not the User / Owner Manual). After looking at that and looking online I learned that there is no sensor for the Flow Sense feature itself. The Flow Sense doesn't detect a blockage. It detects excessive heat and the manufacturer has simply concluded that too much heat is most likely caused by a blocked duct and then it activates the Flow Sense safety feature: cutting off the heat source. Since I knew it was a heat problem I figured I'd get inside and check the two thermostats and the igniter. Igniter was fine, one thermostat was fine, the other one - the High Limit Thermostat - was giving inconsistent readings. I replaced it. Here's how: First I took the dryer apart. This is a little time consuming. There are a lot of parts that need to come out. I recommend that you put the screws in small baggies with a note as to where you took them out of so that you know where they go when you put it back together. You need to remove part of the back, the top and the front. I removed the electrical box because that is what is shown in the manual but I'm not convinced that I needed to. See if you can get the rest of the dryer apart without removing it but if you have to remove it it's not that big of a deal. It's a little tricky to detach the wire harnesses is all. And extra steps, of course. I did not remove the drum. Instead I just reached inside with the front off and pulled the wires off the thermostats to test them for resistance with a multimeter. It was kind of a pain and a little awkward but I did not want to mess with the drum tensioner. Once I figured out that the High Limit Thermostat was the likely culprit I removed it - which required a very short Phillips head screw driver and some patience since I could not actually see one of the screws. But all good. Just remember which wire goes on which terminal. Make a note for yourself: gray back / red front - something like that. Then I ordered the part and installed the new one and rebuilt the dryer in reverse from what I did.

Now, here's the thing: I actually did two things: aside from changing the thermostat I also thoroughly cleaned out the dryer. Somehow a lot of lint built up in there - no idea how since it all appeared to leave the dryer through the vent. but there must be some small gap somewhere. I cleaned everything including the flame detector. When I put it all back together it worked but I'm not 100% sure that the thermostat was bad. It's at least possible that all the lint and dirt was messing with the way the thermostats behaved. So what I would recommend, if you have this problem, is to clean it out first and then put it back together enough to run it and see of the heat comes on. It will take maybe 30-60 seconds for the heat to come on while the igniter lights. If not, go ahead and replace whichever thermostats or other parts you think are broken.

The customer support received from the this site individual. Was professional and very helpful. The video they recommended want me to the replacement part (Thermistor Ntc) step-by-step thanks to this site I had no problem at all

Handed the parts to my son-in-law he's very mechanically inclined had the job done in 20 minutes

I'm not for reading instructions. So I just dove right in and took the dryer apart to get down to the motor. I gave the dryer a thorough cleaning and replaced the 3 parts I ordered from the online recommendation. Wish I would have ordered 2 sensors and the 2 thermostats that are near the burner. Just so replace beings I was in there. Replacing the parts was easy, found them just by looking for matches to the new parts. Reassembled the dryer, dont think I put a single screw back where I got it lol. And still haven't put the top lid back on due to difficulty. Not sure if I even needed any parts, found a nest in my outside vent completely plugging it. But after a good cleaning and replacing the parts the dryer dries the best it has since we've owned it. The dryer came with our house which we bought 3 years ago and it was 2 years old when we purchased the house, so it is now 5 years old.

Removed the old one and put the new one in the slot.

Called Parts Select and assisted me in proper parts needed. Drier works as new.

Took out drum. Found all parts easy to locate. Found defective part and replaced with new one.

Thank you Parts Select for your assistance.

I did not do the repair I hired the propane company to do it . It was too difficult for me.they removed top & front of dryer .removed & replaced gas orfice reinstall all parts that were removed. Install and test dryer IT cost me $91.59 for labor & $24.65 for the part & shipping.If the dryer had a side access near the gas valve it could have saved me the cost of labor. I could have done it myself.

Removed top of dryer
I carefully removed wires from back of control panel
Removed control panel
Most of screws hold cabinet together
Unhook wire from light on door and sensor on the front panel.
Remove the front door and panel together
I changed both front rollers on front panel
If you have to change rear rollers lift tub up by belt
Remove screws on back of dryer that will let you lift out inside rear panel that holds the rear rollers
Change rollers and just revearse procedure to put back together

Following the reference video, step by step and taking progress photos along the way, organizing screws and hardware as they were removed.

The discrepancy I found was the new rollers that I received were complete with the shaft. The video with the older rollers instruct removing the rollers from the shaft.

To use the new rollers with the new shaft, requires removing an additional panel at both the front 2 and also the full back panel for the rear 2, to get a wrench on both ends of the shaft, and then attach the new roller bearing shaft assembly and re-install the panel.

Other than that, it went very smoothly and the result was a quiet rotating drum. No more thumping!

My dryer actually required 2 moisture sensors, but had only ordered one pack, which only came with 1 sensor. For whatever reason, I thought the pack would have had the 2 pieces.

Another reviewer made note to wear work gloves as some of the hardwares metal edges are quite sharp. Following that advice I completed the repair in 3 hours without a scratch. Thanks for the detailed video Partselect team and good luck to all attempting repairs.

Watched a You Tube video

Pull off the top and front of the dryer and reached in and replaced the part it was easy. Had to clean all the dryer out real good with from the lint

Take old one out and slide new filter in.