41782142102 Kenmore Dryer - Instructions

1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Access panel at rear of dryer.
7.Unscrew 3 screws from inside, center rear of drum.
8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit
9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket)
10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer.
11. Vacuum everything--duct, blower, lint trap, ect.
12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside
13. reassemble remainder of parts in reverse order.

Disconect the dryer from the main power source.

1) Remove the two screws from the rear / upper panel (below the control panel).

2) Snap the front side using a flat head screw driver.

3) On the inside front, remove two screws (one on each side) from the upper side and snap the door assembly off.

4) Remove the rear motor access panel (two screws) and appying tension to the spring remove the belt.

5) Pull the drum upwards (verticaly) unnapping it from the rear wall and remove it horizontally through the front panel.

6) Disconect the four leads to the heating element and remove the four screws from the rear of the dryer and replace the heating element.

Follow the same steps backwards to put the dryer together again.

Unplugged Dryer.
Opened top of Dryer, over the drum.
Removed Thermal Limiter.
Tested the Thermal Limiter - found it was open.
Checked all vents and exhaust tube for lint build-up.
Replaced Thermal Limiter.
Closed top of dryer.
Plugged Dryer back.
Tested Dryer - it works.

I found a electrical diagram and some common problems on some websites which led me to check the thermal limiters. There are two right up top near the back of the dryer - one mounted closer to the heating coils and one mounted directly to the sheet metal on the inside back of the dryer. Using an DMM on the "Ohms" setting, I checked each sensor to make sure that they were "closed" (near zero ohms). Sure enough, the sensor mounted on the back of the enclosure was open (high resistance) which prevented the dryer from starting. To confirm, I shorted the two leads going to the sensor together temporarily and wrapped them with electrical tape and then tested the dryer - it worked perfectly. The part from Part Select was ordered and shipped very quickly. Since the sheet metal screws holding the sensor on were difficult to access with the drum in place, I used small machine screws/nuts to fasten the sensor - this allowed me to tighten the nuts from the outside of the dryer, making it very easy to attach.

For the glide, I want to advise people that to replace the entire glide you need to order two front drum glide parts as each is only half.

First, unplug the dryer. Then, open the top so that you can get access to the work area. On each side of the inside front, there is a screw that connects the front panel to the side panels. Unscrew those screws and pull the front panel until it disconnects from the side panels. Be careful as there are wires that are secured to the bottom of the top inside lip of the front panel. One set of wires goes to the light bulb in the dryer door. You don't need to disconnect the wires, but be sure you don't damage the wires by pulling the front panel too far away from the dryer.

Once you have the front panel out of the way, you can see the front drum glide. In my case, one half was loose as the plastic plugs that pop into recesses to hold the glide in place had broken off. Remove the damaged glide section and replace it with the new section, popping the plastic plugs into the recesses. Don't be afraid to slap the glide to lock the plugs in place.

For the felt, I cut the part of the old felt that was pulling away from the front panel. I then used a flat-head screwdriver and wire brush to remove as much of the old adhesive as I could. Then, using the high-heat adhesive that came with the new felt, I put a generous amount on the front panel where the felt needed to go. I used a toothpick to spread the adhesive to get maximum area coverage. I let it set for a minute or two, and then placed the new felt. I used small clamps to keep the felt in place until the adhesive had time to bond. I only kept the clamps in place for 10 minutes.

Once I removed the clamps, I let the felt continue to adhere to the front panel for 24 hours before reassembling the dryer. Again, be careful of the wires connected to the front panel as it appears very easy for them to be pinched or cut when putting the front panel back in place.

When the dryer was reassembled, I plugged it back in and have had no more troubles.

I unlatched top panel then removed two screws holding front panel on. I then lifted drum out of hanger to make room to remove element. Disconnect wires to limit switch and element. I then removed four screws on back of dryer that hold the pan. I removed old assembly and replaced with new one. Assemble in reverse.

removed the screws, disconnected the wires. installed the new elements replaced the wires.

1) Removed Top Dryer Cover (pushed 2 compression clips on front side 1" from top and 2" in from each side) to gain access to terminal block in rear.
2) Removed 2 screws over terminal block cover and 2 screws holding bad terminal block in place. Removed 3 screws holding bad power cord,
3) Removed good terminal connectors from bad terminal block and reinstalled them in the new terminal block.
4) Cut dryer wire from bad terminal block connector and soldered (optional) them to the new terminal block connector. Installed this connector into the new terminal block.
5) Installed new terminal block in dryer with 2 screws.
6) Installed new power cord on new terminal block ensuring contacts were tight and cord had pull guard properly installed. Reinstalled terminal block cover with 2 screws.
7) Reinstalled Dryer Top Cover.

It was too easy: 1) remove the back of the control panel 2) disconnect wires to the switches and mark them for reassembly- I used masking tape and gave each wire and connector a letter- "a" "b" "c" etc; 3) remove the top of dryer by using a flat head screwdriver to pop the 2 pressure fasteners on the front; 4) remove the front of the dryer- remove the 2 screws fastening the front panel to the sides and lift up until the bottom pressure fasteners pop; 5) remove the belt from the pulley and tensioner- I used a digital camera to take pictures so I knew how to re-thread the belt; 6) remove the drum- pull up on the back of the drum with the belt and then pull the drum through the front of the dryer-it's a little smaller than the front opening so you need to pull on the sides of the dryer; 7) replace the heating element by (a) removing the overheat sensor and (b) removing three screws to remove the heating element from the back of the dryer; 8) replacing the rear drum bearing by (a) removing the bearing asssembly from the back of the dryer-2 screws, and (b) removing the bearing roller from the back of the drum- 3 screws; 9) assembly is the reverse of disassembly. Again it's too easy. I'm a lawyer with no mechanical training. Thanks to Parts Select for making finding the parts easy and saving me a lot of money.

The first thing I did was cheked the electrical panel and breaker, then I checked the electrical cord, then I did check the motor on the bottom of the machine (that may be is the blower motor) looking for any indication of burned parts or broken, then I checked the on-off switch with a voltmeter looking for continuity and it was fine. Then I checked the timer switch and it was fine as well. Finally, I took the lid off the top of the dryer machine to check the thermostat and themal limiter fuse. The thermostat was fine but the thermal fuse was open. So after doing some research to understand how the fuse work I decided to place an order to get a new fuse. I installed it and the dryer started working again. After replacing the fuse I monitored the dryer machine while operating it and worked fine. Why the fuse was open or was damaged? It is the first time I have problems w/ the dryer. I checked the end of the conduct line that guide the air out and I noticed and have to clean the end of it because it was dirt. Because it was not completly clean, the dryer got overheated. It took me sometime to figure out the problem but I learned, save me money and the best part was that I do it myself : )

I removed the broken door latch & strike with pliers. Then I pushed the new parts into place

First, I removed the top panel which is held on at the front by pressure clips. Second, I removed the entire front panel which entailed removing 2 screws and 2 wire couplings. Third, I removed the 3 screws on the inside center of the drum which turned out to be unnecessary. Fourth, I slid the drum forward in order to access the rear bearing. Lastly, I replaced the entire bearing assembly including the shaft, bracket, bearing, grounding ball and clip. Again, probably not needed but I had ordered the parts in advance in preparation for the worst.

I took the new latch out of the package and snapped it into place. It took about 15 seconds, and that included the walk to the laundry room!

I waded into this project without knowing what I was doing and as a result did much more work than was needed. What I should have done was 1) open access panel at lower left of back of dryer and rmove belt from pully 2) push screwdriver in against clips in seem at top front of dryer (where top meets face) and lift top up and off hinges at back 3) remove screws holding front of dryer to the sides of the dryer cabinet (about 1 foot down) and swing front down on hinges at bottom 4) lift dryer drum straight up out of the bracket at the back of the dryer 5) remove wires from the dryer element and heat sensor on the heater pan (about 4 and 1 o'clock respectively wires are on tight, may need plieres) 6) unscrew heater pan from back of dryer 7) remove heat sensor from old heater pan and put on new heater pan 8) screw new heater pan to back of dryer 9) replace wires to elements and sensor, you may want to "crimp" the connectors onto the tabs 10) replace dryer drum slipping back into back bracket, be sure that dryer belt is around drum as when you openned the dryer 11) lift up front so that drum fits around and is supported by flange molded into front 12) replace screws that attach front to dryer cabinet 13) replace top of dryer (put back on hinges at back and lower onto clips in front 14) put dryer belt back on pully and replace access plate.

first i used a flathead to lift up the top of the dryer. there were two prongs that you press in to detach the top.

then there were two screws on the inside along each side that i needed a phillips to remove. one screw on each side.

i also needed to detach a cable and cut the tie.
from there, it was easy to pull off the front of the dryer.

the first noticeable thing was HOW much lint there was inside! so out came the vacuum and away went all the dust and lint.. a TON of it.

then i used a sharp knife to remove all the existing upper and lower felt. that took awhile, and i got as much as i could.

then i applied the TOP felt, nice and center, and from there, the FELT was applied, which fit perfectly. I let it dry/set for about 2 hours.

for the Front drum glide, AN IMPORTANT NOTE! i ordered only ONE drum glide, but you need TWO! I had to order a second one, and i dont know why they dont come in pairs.. so the front drum glides snap on pretty easily to the front of the drum. press hard and they SNAP into place. once they are snapped on, you just put back on the front, replace the screws, re-connect and re-tie the cable, and close the lid!