Models
>
NVL333EB0CC
NVL333EB0CC Hotpoint Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for NVL333EB0CC
Viewing 4 of 4Keep searches simple, eg. "belt" or "pump".
$54.65
This part is used to start the dryer once you have selected a setting on the timer.
In Stock
In Stock
In Stock
Bearing Only. This part helps your appliance run as quietly as possible.
No Longer Available
$134.25
This kit comes with the rear bearing, shaft support, lubricant and other items required for the installation.
In Stock
On Order
In Stock
$73.67
This hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 260 degrees...
In Stock
$78.40
This thermostat controls the internal drying temperature.
Cycling themostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermos...
In Stock
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for NVL333EB0CC
Viewing 2 of 2Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jaren from Lemoore, CA
- Parts Used:
- WE4X881
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken Knob Post
First I unplugged the dryer, then I removed the access panel on the back of the control panel. I removed the wires from the back of the switch...Here is where I messed up. I removed the switch prior to ordering the part, the bad part is the way I removed the part. When you get the new part in you will be able to see how it will be mounted
... Read more
to the control panel. I had no idea, so I did what was necessary to remove it. Needless to say, I bent the hell out of the hole that the switch mounts in. In turn, the installation of the new switch did not go as easily as I would have liked. After straightening out some metal and drowning the thing in epoxy, the new switch is installed. I hooked the wires back up on the back of the switch, plug in the dryer, and dry some clothes. Standing victorious over the dryer with beer in hand, not only did I accomplish the mission but I learned my lesson... destructive removal = BAD!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raul from Fountain, CO
- Parts Used:
- WE12X10009, WE25X10001, WE03X10001
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Loud noise & clothes hanging in drum.
1. Remove power cord from wall outlet. Unlatched the top lid of the dryer by pushing a flat screwdriver under the R & L sides where a metal clip on each side holds the top down.
2. Removed the yellow clip screwed onto the top frame.
3. Removed the front frame of the dryer by unscrewing the two screws holding the front frame on ... Read more – one on either side.
4. Mark w/ an (x) on same side of alignment for the 2 wiring connectors before separating them.
5. Removed the front panel by tilting it forward & lifted to unlatch it from the 2 clips at the bottom of dryer.
6. Unwound the belt encircling the drum by releasing the tension between the tensioner roller & drive pulley. (Its better to remove back access panel at this time & do this at the back since I found it necessary to do this anyway when re-installing the new belt).
7. W/ lifting motion, pulled the drum out from the plastic holder attached to the back of the dryer frame. Guided & completely removed the drum out of the dryer.
8. Unscrewed the 3 screws holding the old big bearing to the back of the drum.
8. Unscrewed the 2 screws & removed the plastic that had held the bearing at back of the frame.
8. Installed the new bearing by screwing it to the back of the drum with 3 screws. Be careful not to strip screws. Used help to hold new bearing in place & aligned w/ screws.
9. From the front, installed the plastic holder to the back of the frame by 2 screws and put the ball bearing in-between holder & the metal strip retainer coming from the back of dryer.
10. Used the grease that came with the kit on the plastic holder & the big bearing at the back of the drum.
11. Replaced w/ new belt then re-inserted the drum back into the body of the dryer frame, w/ lifting motion, re-inserted the bearing into the plastic holder.
12. Putting the belt into the drive & tension pulleys through the back access panel was easy but could be very hard to do if coming from the front.
13. Had to replace the front panel's top felt w/ glides that holds the drum at the front w/ a new one. Really important to pay attention to where the plastic glides excess portion is facing (towards front panel), otherwise the front panel might not fit when you snap it back to place.
14. Removed old felt remnants w/ blade scraper & sandpaper. Used adhesive that came w/ kit. Once tacky, put the new felt w/ glides on & used clamps to hold it in place.
15. Waited for 2 hrs. (watched a movie) then re-installed front panel. Make sure that the drum (front) lid rides on top of the plastic glides.
16. Latched bottom of front panel to the metal clips. Replace the 2 screws back into place holding the front panel.
17. Snapped the wiring connectors in place where the (x) marks align.
18. Lowered the top panel & snapped it back into place
Note: All parts came w/ fast delivery & OEM fit - very satisfied! Took my time & on every chance I cleaned & vacuumed all areas of lint & dirt since the dryer hasn't been serviced for more than 10 years...
2. Removed the yellow clip screwed onto the top frame.
3. Removed the front frame of the dryer by unscrewing the two screws holding the front frame on ... Read more – one on either side.
4. Mark w/ an (x) on same side of alignment for the 2 wiring connectors before separating them.
5. Removed the front panel by tilting it forward & lifted to unlatch it from the 2 clips at the bottom of dryer.
6. Unwound the belt encircling the drum by releasing the tension between the tensioner roller & drive pulley. (Its better to remove back access panel at this time & do this at the back since I found it necessary to do this anyway when re-installing the new belt).
7. W/ lifting motion, pulled the drum out from the plastic holder attached to the back of the dryer frame. Guided & completely removed the drum out of the dryer.
8. Unscrewed the 3 screws holding the old big bearing to the back of the drum.
8. Unscrewed the 2 screws & removed the plastic that had held the bearing at back of the frame.
8. Installed the new bearing by screwing it to the back of the drum with 3 screws. Be careful not to strip screws. Used help to hold new bearing in place & aligned w/ screws.
9. From the front, installed the plastic holder to the back of the frame by 2 screws and put the ball bearing in-between holder & the metal strip retainer coming from the back of dryer.
10. Used the grease that came with the kit on the plastic holder & the big bearing at the back of the drum.
11. Replaced w/ new belt then re-inserted the drum back into the body of the dryer frame, w/ lifting motion, re-inserted the bearing into the plastic holder.
12. Putting the belt into the drive & tension pulleys through the back access panel was easy but could be very hard to do if coming from the front.
13. Had to replace the front panel's top felt w/ glides that holds the drum at the front w/ a new one. Really important to pay attention to where the plastic glides excess portion is facing (towards front panel), otherwise the front panel might not fit when you snap it back to place.
14. Removed old felt remnants w/ blade scraper & sandpaper. Used adhesive that came w/ kit. Once tacky, put the new felt w/ glides on & used clamps to hold it in place.
15. Waited for 2 hrs. (watched a movie) then re-installed front panel. Make sure that the drum (front) lid rides on top of the plastic glides.
16. Latched bottom of front panel to the metal clips. Replace the 2 screws back into place holding the front panel.
17. Snapped the wiring connectors in place where the (x) marks align.
18. Lowered the top panel & snapped it back into place
Note: All parts came w/ fast delivery & OEM fit - very satisfied! Took my time & on every chance I cleaned & vacuumed all areas of lint & dirt since the dryer hasn't been serviced for more than 10 years...
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristian from Jackson, WY
- Parts Used:
- WE14X10015
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Heat!
Unplug power. Take the top off. Take front off, unplug the two wire connections. Undo belt from back access. Pull up on drum and remove. Unscrew 4 screws that hold on the element housing, remove. Reverse steps to put back together.
Was this instruction helpful to you?
Thank you for voting!