Models
>
DCXH46EA0WW
DCXH46EA0WW General Electric Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for DCXH46EA0WW
Viewing 4 of 4Keep searches simple, eg. "belt" or "pump".
$34.80
If your dryer is noisy while tumbling, you may need to replace the drum glides. This genuine OEM part is found attached to the front panel of your dryer. It is used to reduce friction and allows the d...
In Stock
In Stock
$116.35
***Please Note: This part is a substituted part by the manufacturer. It may appear different, but should still work with your appliance.
In Stock
On Order
In Stock
$268.42
This dryer timer is used to control the unit's cycles by regulating the length of time that power is directed to each setting.
In Stock
In Stock
On Order
$79.82
This part is found in the same location as the Terminal Block at the back of the Dryer. It acts as a safety device which prevents your appliance from overheating.
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for DCXH46EA0WW
Viewing 3 of 3Noisy
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Boise, ID
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Drum glide wore down and caused close to get stuck between drum and front panel.
Unpluged dryer. Removed the top of dryer by pushing in a retaining clip on both sides of the front lip with a screw driver. Remove the two screws on both sides of front panel. These screws are square head or phillips #2. Unplugged the wiring harness to front panel (make sure power has been disconnected). Support drum and lean front pa
... Read more
nel away from dryer body. Front panel will pull off of tabs at bottom. The old drum glide is fiberous and hard to remove. I removed most of it with the pliers, but had to carefully scrape the balance of the glide off with the wood chisel. The adhesive that comes with the repair part has an acetone base, so I used acetone (or you could use nail polish remover) to remove the old adhesive. Once the acetone has dried, I applied an 1/8" snaking bead of adhesive to the front panel. There is more adhesive in the tube than you need so do not use too much. Make sure that you get adhesive as close to the base of the lower seal as you can. Follow directions on adhesive tube and then attach the glide. I let it set up for about 30 seconds. Place the front panel back on the tabs of the dryer. Carefully lift the drum an fit it on the front panel and insert the two screws holding the panel to the base. Reconnect the wiring harness and make sure it is not in contact with the drum. Check to make sure that all of the electrical connectors on the timer are still in place. Reassemble the dryer. Reconnect power.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Grand Prairie, TX
- Parts Used:
- 134101400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Terminal Block Melts when power cord connector is left loose by install crew.
1) Removed Top Dryer Cover (pushed 2 compression clips on front side 1" from top and 2" in from each side) to gain access to terminal block in rear.
2) Removed 2 screws over terminal block cover and 2 screws holding bad terminal block in place. Removed 3 screws holding bad power cord,
3) Removed good terminal connectors from ... Read more bad terminal block and reinstalled them in the new terminal block.
4) Cut dryer wire from bad terminal block connector and soldered (optional) them to the new terminal block connector. Installed this connector into the new terminal block.
5) Installed new terminal block in dryer with 2 screws.
6) Installed new power cord on new terminal block ensuring contacts were tight and cord had pull guard properly installed. Reinstalled terminal block cover with 2 screws.
7) Reinstalled Dryer Top Cover.
2) Removed 2 screws over terminal block cover and 2 screws holding bad terminal block in place. Removed 3 screws holding bad power cord,
3) Removed good terminal connectors from ... Read more bad terminal block and reinstalled them in the new terminal block.
4) Cut dryer wire from bad terminal block connector and soldered (optional) them to the new terminal block connector. Installed this connector into the new terminal block.
5) Installed new terminal block in dryer with 2 screws.
6) Installed new power cord on new terminal block ensuring contacts were tight and cord had pull guard properly installed. Reinstalled terminal block cover with 2 screws.
7) Reinstalled Dryer Top Cover.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Schenectady, NY
- Parts Used:
- 131930600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Timer Inoperative
1) Disconnect dryer from power.
2) Use a large standard screwdiver to push in 2 clips on the front side of the dryer between the main body and hood. Hood then lifts up on hinges mounted in the back. Secure hood.
3) Pull off timer knob and remove 2 screws.
4) Write down the color sequence of wires attached to old timer.
... Read more />5) Remove wires to old timer using needle nose plyers grasped at the wire connector.
6) Attach wires in the correct sequence to new timer and reassemble dryer.
2) Use a large standard screwdiver to push in 2 clips on the front side of the dryer between the main body and hood. Hood then lifts up on hinges mounted in the back. Secure hood.
3) Pull off timer knob and remove 2 screws.
4) Write down the color sequence of wires attached to old timer.
... Read more />5) Remove wires to old timer using needle nose plyers grasped at the wire connector.
6) Attach wires in the correct sequence to new timer and reassemble dryer.
Read less
Was this instruction helpful to you?
Thank you for voting!