UPGT650EH0MG General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dan from Mineola, TX
- Parts Used:
- WE03X10008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
There was a grinding noise while the dryer was being used.
We removed the top and front of the dryer and found that the drum roller bearings had gone out on one side. All this happenend on a weekend with no reair store open. We googled the cut sheet for the dryer, found the part number we needed and ordered the parts (we went ahead and replaced both rollers) from partselect.com. For $70 and our own labor, we completed the repair by Wednesday evening. I feel certain we saved at least $100 if not more by doing the work ourselves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from Los Altos, CA
- Parts Used:
- WE18X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacement of filter
It wasn't a repair - just replaced a filter that was wearing out in one spot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from FREEHOLD, NJ
- Parts Used:
- WE12X10011, WE03X10008
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Noise and Squeaking from Front During Drying
Front roller bearings were bad and figured to do the belt while in there. I bought the manual online which was very helpful.
??
Unplug dryer
Remove 4 screws behind touch panel
Tilt panel forward then up leaving wires attached
Rear has 2 screws on the rear ends facing down remove them at ends
Lift rear up then forward push and top will be freed (keep on top)
Front edges have 1 screw each but sharp areas watch
Open door and remove x 4 screws then lift up and forward bottom has tabs each end to hold in place
Wires for light and switch can stay attached, move front/door to side
Exposed will be the drum brace.. I changed the x 2 rollers while the drum brace was in place.
To undo the rollers you have to use a wrench to reach in as you use a nut driver to remove then re-install new roller with washer on inside and outside (pay attention when you remove)
Remove x 4 small screws..... hold drum inside then lift brace up and forward
Have assistance hold drum steady with pressure to the back otherwise you will have to align back to the rear rollers
Reach into the bottom for the idle pulley to remove drive belt tension... drive belt is VERY SKINNY and has ribbed side that faces the drum.
Reverse the steps..
??
Unplug dryer
Remove 4 screws behind touch panel
Tilt panel forward then up leaving wires attached
Rear has 2 screws on the rear ends facing down remove them at ends
Lift rear up then forward push and top will be freed (keep on top)
Front edges have 1 screw each but sharp areas watch
Open door and remove x 4 screws then lift up and forward bottom has tabs each end to hold in place
Wires for light and switch can stay attached, move front/door to side
Exposed will be the drum brace.. I changed the x 2 rollers while the drum brace was in place.
To undo the rollers you have to use a wrench to reach in as you use a nut driver to remove then re-install new roller with washer on inside and outside (pay attention when you remove)
Remove x 4 small screws..... hold drum inside then lift brace up and forward
Have assistance hold drum steady with pressure to the back otherwise you will have to align back to the rear rollers
Reach into the bottom for the idle pulley to remove drive belt tension... drive belt is VERY SKINNY and has ribbed side that faces the drum.
Reverse the steps..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cary from WEST JORDAN, UT
- Parts Used:
- WE03X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Drum rolls where bad
Pulled top covers puller front panel pulled drum forward pulled plastic clips installed rollers and put back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilbert from West Jordan, UT
- Parts Used:
- WE01X28316, WE01X10184
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The Door Latch fell apart
I ordered the parts that were easy to locate on the web site and the fix took me 5 minutes to fix great job i love this site.
Was this instruction helpful to you?
Thank you for voting!