Models
>
GFDN160GJ0WW
GFDN160GJ0WW General Electric Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GFDN160GJ0WW
Viewing 7 of 7
Keep searches simple, eg. "belt" or "pump".
$11.56
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
In Stock
$36.13
This 89.5-inch drive belt is for dryers. It has a 4-rib design on the inside for a better grip. If comparing the size of your current belt to the new one, keep in mind that a small amount of stretchin...
In Stock
$9.25
If the lightbulb inside your dryer drum has burned out, this is an authentic OEM replacement. It is a 10W, 120V bulb that is sold individually. The bulb turns on when the dryer door is open and should...
In Stock
In Stock
In Stock
If your dryer is excessively noisy when operating, is not tumbling, or is leaving marks on your laundry, it may be time to replace the drum glides. The drum glide bearing is a genuine OEM part for you...
In Stock
If your dryer is making a squealing, metal-on-metal noise you may need to replace your slide bearings. These slide bearings are genuine OEM replacement parts that measure approximately 3 inches in len...
No Longer Available
$27.45
This interlock switch is a genuine OEM part that can be used in a variety of appliances like dishwashers and dryers. The switch is also known as a belt switch and works as a simple on and off mechanis...
In Stock
In Stock
$9.01
This is a replacement O-ring for the drum bearing retainer on your dryer. The drum bearing is found at the back of the dryer drum. The O-ring is designed to create a seal on the drum bearing. The O-r...
In Stock
$32.49
A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.
In Stock
$16.51
The adjustable leveling screws on the bottom of your dryer can be screwed in or out to lower or raise the leg level. If one of the leveling screws is stripped, damaged, or missing, you may not be able...
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for GFDN160GJ0WW
Viewing 9 of 9Noisy
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Too hot
Fixed by these parts
How to fix it
Not Heating
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Adrian from Middletown, MD
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum belt broke
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on.
This was a first attempt ever at fixing an appliance and it was no big deal.
This was a first attempt ever at fixing an appliance and it was no big deal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary L. from Freeport, IL
- Parts Used:
- WE04X25996, WE4X448
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
The dryer drum turned ok, but the gas heat did not start.
First I found and watched three videos on how to open the dryer and replace the igniter.
Then I opened the dryer, but I did not remove the belt as suggested in the video, and then I removed the ignitor and flame detecter as the videos had shown.
I got on-line and ordered the new parts from PartsSelect in the afternoon and had t ... Read more hem in my hands the next morning by 9:30 am.
I installed the new parts and everything worked fine again. You must be very careful with the igniter to not touch it with hands or anything else. I practiced puting in the old parts first.
Then I opened the dryer, but I did not remove the belt as suggested in the video, and then I removed the ignitor and flame detecter as the videos had shown.
I got on-line and ordered the new parts from PartsSelect in the afternoon and had t ... Read more hem in my hands the next morning by 9:30 am.
I installed the new parts and everything worked fine again. You must be very careful with the igniter to not touch it with hands or anything else. I practiced puting in the old parts first.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshua from Dallas, TX
- Parts Used:
- WE4M415
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Dryer would not start
The end repair was very simple and took minimal effort. The time and difficulty was all in the testing. I disassembled the dryer and removed the drum and then hard wired each thermo-fuse to determine where the fault was. After test all of those I was stumped. When I opened the door the light would not come on so I assumed it was a pow
... Read more
er fault closer to the source. However after all of my testing I couldn't find anything wrong. I then removed the light bulb and realized it was burned out which led me to the door switch being the fault. I removed the switch and soldered the three wire together and the dryer started right up! All I had to do was order a new $15 part, unsolder the wires and plug them in. Would have been so much simpler if that light bulb hadn't of been burned out causing me to over think my diagnosis. This was my first major appliance repair and I did it with only the help of the parts diagram provided on the website.
Read less
Was this instruction helpful to you?
Thank you for voting!